On Tue, Mar 31, 2020 at 1:44 AM Jagan Teki <ja...@amarulasolutions.com> wrote:
>
> Hi Chen-Yu,
>
> On Fri, Mar 27, 2020 at 10:12 AM Chen-Yu Tsai <w...@kernel.org> wrote:
> >
> > From: Chen-Yu Tsai <w...@csie.org>
> >
> > The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
> > card size development board based on the Rockchip RK3328 SoC, with:
> >
> > - 1/2/4 GB DDR4 DRAM
> > - eMMC connector for optional module
> > - micro SD card slot
> > - 1 x USB 3.0 host port
> > - 2 x USB 2.0 host port
> > - 1 x USB 2.0 OTG port
> > - HDMI video output
> > - TRRS connector with audio and composite video output
> > - gigabit Ethernet
> > - consumer IR receiver
> > - debug UART pins
> >
> > The ROC-RK3328-CC has the enable pin of the SD card power switch tied
> > to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
> > muxed by default. SDMMC0_PWREN is an active high signal controlled by
> > the MMC controller, however the switch enable is active low, and
> > pulled low (enabled) by default to make things work on boot.
> >
> > As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
> > power to the card. The default GPIO state for the pin is pull-down and
> > input, which doesn't require extra configuration when paired with the
> > external pull-down and active low switch.
> >
> > Thus we make a custom target for this board and do the muxing in its
> > spl_board_init() function.
> >
> > The device tree file is synced from the Linux kernel next-20200324.
> >
> > Signed-off-by: Chen-Yu Tsai <w...@csie.org>
> > ---
>
> [snip]
>
> > diff --git a/board/firefly/roc-cc-rk3328/MAINTAINERS
> > b/board/firefly/roc-cc-rk3328/MAINTAINERS
> > new file mode 100644
> > index 000000000000..f2318e71ac33
> > --- /dev/null
> > +++ b/board/firefly/roc-cc-rk3328/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +ROC-RK3328-CC
> > +M: Loic Devulder <ldevul...@suse.com>
> > +M: Chen-Yu Tsai <w...@csie.org>
> > +S: Maintained
> > +F: board/firefly/roc-cc-rk3328/
> > +F: configs/roc-rk3328-cc_defconfig
> > +F: arch/arm/dts/rk3328-roc-cc-u-boot.dtsi
> > diff --git a/board/firefly/roc-cc-rk3328/Makefile
> > b/board/firefly/roc-cc-rk3328/Makefile
> > new file mode 100644
> > index 000000000000..1550b5f5f16e
> > --- /dev/null
> > +++ b/board/firefly/roc-cc-rk3328/Makefile
> > @@ -0,0 +1 @@
> > +obj-y := board.o
> > diff --git a/board/firefly/roc-cc-rk3328/board.c
> > b/board/firefly/roc-cc-rk3328/board.c
> > new file mode 100644
> > index 000000000000..eca58c86b53e
> > --- /dev/null
> > +++ b/board/firefly/roc-cc-rk3328/board.c
> > @@ -0,0 +1,38 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * (C) Copyright 2020 Chen-Yu Tsai <w...@csie.org>
> > + */
> > +#include <asm/io.h>
> > +
> > +#include <asm/arch-rockchip/grf_rk3328.h>
> > +#include <asm/arch-rockchip/hardware.h>
> > +
> > +#if defined(CONFIG_SPL_BUILD)
> > +
> > +#define GRF_BASE 0xFF100000
> > +
> > +enum {
> > + GPIO_0_D6_GPIO = 0 << 12,
> > + GPIO_0_D6_MASK = 0x3 << 12
> > +};
> > +
> > +/*
> > + * The ROC-RK3328-CC has the enable pin of the SD card power switch tied
> > + * to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
> > + * muxed by default. SDMMC0_PWREN is an active high signal controlled by
> > + * the MMC controller, however the switch enable is active low, and
> > + * pulled low (enabled) by default to make things work on boot.
> > + *
> > + * As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
> > + * power to the card. The default GPIO state for the pin is pull-down and
> > + * input, which doesn't require extra configuration when paired with the
> > + * external pull-down and active low switch.
> > + */
> > +void spl_board_init(void)
> > +{
> > + struct rk3328_grf_regs * const grf = (void *)GRF_BASE;
> > +
> > + rk_clrsetreg(&grf->gpio0d_iomux, GPIO_0_D6_MASK, GPIO_0_D6_GPIO);
> > +}
>
> So, this seem toggle the bit 12, 13 of GRF_GPIO0D_IOMUX so-that it
> operate like a gpio(not like default sdmmc0_pwrenm1), isn't it
> required for the next stages like U-Boot proper and Linux? these has
> vcc_sd node where it operates a fixed regulator to active low the same
> pin.
>
> gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
So U-boot proper and Linux both have pinctrl and GPIO and all the stuff
to deal with this. SPL doesn't have GPIO enabled, and I believe all the
pinctrl properties are striped out. (BTW, not sure why we're enabling
pinctrl driver support in SPL if nothing is triggering them.) It seems
a bit heavy pulling all that stuff in just for one pin mux in SPL. The
same is also done for the UART pins.
ChenYu
