Hi Walter,
On Wed, Mar 04 2020, Walter Lozano wrote:
> In SPL legacy code only one MMC device is created, based on BOOT_CFG
> register, which can be either SD or eMMC. In this context
> board_boot_order return always MMC1 when configure to boot from
> SD/eMMC. After switching to DM both SD and eMMC devices are created
> based on the information available on DT, but as board_boot_order
> only returns MMC1 is not possible to boot from eMMC.
>
> This patch customizes board_boot_order taking into account BOOT_CFG
> register to point to correct MMC1 / MMC2 device.
>
> Signed-off-by: Walter Lozano <walter.loz...@collabora.com>
> ---
> board/solidrun/mx6cuboxi/mx6cuboxi.c | 49 ++++++++++++++++++++++++++++
> 1 file changed, 49 insertions(+)
>
> diff --git a/board/solidrun/mx6cuboxi/mx6cuboxi.c
> b/board/solidrun/mx6cuboxi/mx6cuboxi.c
> index 71c77ad2a2..3ce122e8b9 100644
> --- a/board/solidrun/mx6cuboxi/mx6cuboxi.c
> +++ b/board/solidrun/mx6cuboxi/mx6cuboxi.c
> @@ -649,6 +649,55 @@ int board_fit_config_name_match(const char *name)
> return strcmp(name, tmp_name);
> }
>
> +void board_boot_order(u32 *spl_boot_list)
> +{
> + struct src *psrc = (struct src *)SRC_BASE_ADDR;
> + unsigned int reg = readl(&psrc->sbmr1) >> 11;
> + u32 boot_mode = imx6_src_get_boot_mode() & IMX6_BMODE_MASK;
> + unsigned int bmode = readl(&src_base->sbmr2);
This is duplication of the logicpd/imx6 board code. But..
> +
> + /* If bmode is serial or USB phy is active, return serial */
> + if (((bmode >> 24) & 0x03) == 0x01 || is_usbotg_phy_active()) {
> + spl_boot_list[0] = BOOT_DEVICE_BOARD;
> + return;
> + }
> +
> + switch (boot_mode >> IMX6_BMODE_SHIFT) {
> + case IMX6_BMODE_NAND_MIN ... IMX6_BMODE_NAND_MAX:
> + spl_boot_list[0] = BOOT_DEVICE_NAND;
> + break;
... we have no raw NAND device on Hummingboard.
> + case IMX6_BMODE_SD:
> + case IMX6_BMODE_ESD:
> + case IMX6_BMODE_MMC:
> + case IMX6_BMODE_EMMC:
> + /*
> + * Upon reading BOOT_CFG register the following map is done:
> + * Bit 11 and 12 of BOOT_CFG register can determine the current
> + * mmc port
> + * 0x1 SD2
> + * 0x2 SD3
> + */
> +
> + reg &= 0x3; /* Only care about bottom 2 bits */
> + switch (reg) {
> + case 1:
> + spl_boot_list[0] = BOOT_DEVICE_MMC1;
> + break;
> + case 2:
> + spl_boot_list[0] = BOOT_DEVICE_MMC2;
> + break;
This code is very similar to setup_iomux_mmc(). Maybe an opportunity to share
code between functions?
Thanks,
baruch
> + }
> + break;
> + default:
> + /* By default use USB downloader */
> + spl_boot_list[0] = BOOT_DEVICE_BOARD;
> + break;
> + }
> +
> + /* As a last resort, use serial downloader */
> + spl_boot_list[1] = BOOT_DEVICE_BOARD;
> +}
> +
> #ifdef CONFIG_SPL_BUILD
> #include <asm/arch/mx6-ddr.h>
> static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
--
http://baruch.siach.name/blog/ ~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- bar...@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -
