On 1/28/20 10:11 AM, Patrick Delaunay wrote:
> Update readme:
> - list the supported SOC and change family to STM32MP15x
> - add warning on OTP write and prerequisite:
> check if MAC address is not yet provisioned.
> - Use filesize for mmc write command (avoid to write all partition
> with ${partsize}). ${filesize} and ${partsize} are set by previous
> load command.
>
> Signed-off-by: Patrick Delaunay <patrick.delau...@st.com>
> ---
>
> board/st/stm32mp1/README | 52 ++++++++++++++++++++++++++--------------
> 1 file changed, 34 insertions(+), 18 deletions(-)
>
> diff --git a/board/st/stm32mp1/README b/board/st/stm32mp1/README
> index f2069bcefa..5d7465a8c8 100644
> --- a/board/st/stm32mp1/README
> +++ b/board/st/stm32mp1/README
> @@ -3,8 +3,8 @@ SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> # Copyright (C) 2018 STMicroelectronics - All Rights Reserved
> #
>
> -U-Boot on STMicroelectronics STM32MP1
> -======================================
> +U-Boot on STMicroelectronics STM32MP15x
> +=======================================
>
> 1. Summary
> ==========
> @@ -12,12 +12,12 @@ This is a quick instruction for setup stm32mp1 boards.
>
> 2. Supported devices
> ====================
> -U-Boot supports one STMP32MP1 SoCs: STM32MP157
> +U-Boot supports STMP32MP15x SoCs: STM32MP157, STM32MP153 and STM32MP151
>
> -The STM32MP157 is a Cortex-A MPU aimed at various applications.
> +The STM32MP15x is a Cortex-A MPU aimed at various applications.
> It features:
> -- Dual core Cortex-A7 application core
> -- 2D/3D image composition with GPU
> +- Dual core Cortex-A7 application core (Single on STM32MP151)
> +- 2D/3D image composition with GPU (only on STM32MP157)
> - Standard memories interface support
> - Standard connectivity, widely inherited from the STM32 MCU family
> - Comprehensive security support
> @@ -37,11 +37,11 @@ And the necessary drivers
> 4. Fuse
>
> Currently the following boards are supported:
> -+ stm32mp157c-ev1
> -+ stm32mp157c-ed1
> -+ stm32mp157a-dk1
> -+ stm32mp157c-dk2
> -+ stm32mp157a-avenger96
> ++ stm32mp157a-avenger96.dts
> ++ stm32mp157a-dk1.dts
> ++ stm32mp157c-dk2.dts
> ++ stm32mp157c-ed1.dts
> ++ stm32mp157c-ev1.dts
>
> 3. Boot Sequences
> =================
> @@ -74,7 +74,7 @@ with FSBL = First Stage Bootloader
> U-Boot is running in secure mode and provide a secure monitor to the
> kernel
> with only PSCI support (Power State Coordination Interface defined by
> ARM).
>
> -All the STM32MP1 boards supported by U-Boot use the same generic board
> +All the STM32MP15x boards supported by U-Boot use the same generic board
> stm32mp1 which support all the bootable devices.
>
> Each board is configurated only with the associated device tree.
> @@ -108,7 +108,7 @@ the supported device trees for stm32mp157 are:
> + install package needed in U-Boot makefile
> (libssl-dev, swig, libpython-dev...)
> + install ARMv7 toolchain for 32bit Cortex-A (from Linaro,
> - from SDK for STM32MP1, or any crosstoolchains from your distribution)
> + from SDK for STM32MP15x, or any crosstoolchains from your distribution)
>
> 2. Set the cross compiler:
>
> @@ -323,8 +323,7 @@ c) copy U-Boot in first GPT partition of eMMC
> # ext4load mmc 0:4 0xC0000000 u-boot.img
> # mmc dev 1
> # part start mmc 1 1 partstart
> - # part size mmc 1 1 partsize
> - # mmc write ${fileaddr} ${partstart} ${partsize}
> + # mmc write ${fileaddr} ${partstart} ${filesize}
>
> To boot from eMMC, select BootPinMode = 0 1 0 and reset.
>
> @@ -334,14 +333,27 @@ To boot from eMMC, select BootPinMode = 0 1 0 and reset.
> Please read doc/README.enetaddr for the implementation guidelines for mac id
> usage. Basically, environment has precedence over board specific storage.
>
> -Mac id storage and retrieval in stm32mp otp :
> +For STMicroelectonics board, it is retrieved in STM32MP15x otp :
> - OTP_57[31:0] = MAC_ADDR[31:0]
> - OTP_58[15:0] = MAC_ADDR[47:32]
>
> To program a MAC address on virgin OTP words above, you can use the fuse
> command
> on bank 0 to access to internal OTP:
>
> - example to set mac address "12:34:56:78:9a:bc"
> + Prerequisite: check if a MAC address isn't yet programmed in OTP
> +
> + 1- check OTP: their value must be equal to 0
> +
> + STM32MP> fuse sense 0 57 2
> + Sensing bank 0:
> + Word 0x00000039: 00000000 00000000
> +
> + 2- check environment variable
> +
> + STM32MP> env print ethaddr
> + ## Error: "ethaddr" not defined
> +
> + Example to set mac address "12:34:56:78:9a:bc"
>
> 1- Write OTP
> STM32MP> fuse prog -y 0 57 0x78563412 0x0000bc9a
> @@ -355,9 +367,13 @@ on bank 0 to access to internal OTP:
> ### Setting environment from OTP MAC address = "12:34:56:78:9a:bc"
>
> 4 check env update
> - STM32MP> print ethaddr
> + STM32MP> env print ethaddr
> ethaddr=12:34:56:78:9a:bc
>
> +warning:: This MAC address provisioning can't be executed twice on the same
> + board as the OTP are protected. It is already done for the board
> + provided by STMicroelectronics.
> +
> 10. Coprocessor firmware
> ========================
>
Reviewed-by: Patrice Chotard <patrice.chot...@st.com>
Thanks
