This device should use ready-gpios rather than ready-gpio. Fix it.
Signed-off-by: Simon Glass <s...@chromium.org>
---
arch/x86/dts/chromebook_coral.dts | 2 +-
doc/device-tree-bindings/gpio/intel,apl-gpio.txt | 2 +-
.../interrupt-controller/intel,acpi-gpe.txt | 2 +-
drivers/tpm/cr50_i2c.c | 2 +-
4 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/x86/dts/chromebook_coral.dts
b/arch/x86/dts/chromebook_coral.dts
index 4e8c0a6c8a..7ba38d7791 100644
--- a/arch/x86/dts/chromebook_coral.dts
+++ b/arch/x86/dts/chromebook_coral.dts
@@ -292,7 +292,7 @@
reg = <0x50>;
compatible = "google,cr50";
u-boot,i2c-offset-len = <0>;
- ready-gpio = <&gpio_n 28 GPIO_ACTIVE_LOW>;
+ ready-gpios = <&gpio_n 28 GPIO_ACTIVE_LOW>;
interrupts-extended = <&acpi_gpe 0x3c 0>;
};
};
diff --git a/doc/device-tree-bindings/gpio/intel,apl-gpio.txt
b/doc/device-tree-bindings/gpio/intel,apl-gpio.txt
index e27a40b437..e12dc37233 100644
--- a/doc/device-tree-bindings/gpio/intel,apl-gpio.txt
+++ b/doc/device-tree-bindings/gpio/intel,apl-gpio.txt
@@ -47,7 +47,7 @@ Example:
reg = <0x50>;
compatible = "google,cr50";
u-boot,i2c-offset-len = <0>;
- ready-gpio = <&gpio_n GPIO_28 GPIO_ACTIVE_LOW>;
+ ready-gpios = <&gpio_n GPIO_28 GPIO_ACTIVE_LOW>;
};
};
diff --git a/doc/device-tree-bindings/interrupt-controller/intel,acpi-gpe.txt
b/doc/device-tree-bindings/interrupt-controller/intel,acpi-gpe.txt
index d9252bf29f..2fe02d8a22 100644
--- a/doc/device-tree-bindings/interrupt-controller/intel,acpi-gpe.txt
+++ b/doc/device-tree-bindings/interrupt-controller/intel,acpi-gpe.txt
@@ -25,6 +25,6 @@ Example:
tpm@50 {
reg = <0x50>;
compatible = "google,cr50";
- ready-gpio = <&gpio_n 0x1c GPIO_ACTIVE_LOW>;
+ ready-gpios = <&gpio_n 0x1c GPIO_ACTIVE_LOW>;
interrupts-extended = <&acpi_gpe 0x3c 0>;
};
diff --git a/drivers/tpm/cr50_i2c.c b/drivers/tpm/cr50_i2c.c
index 1af943d6ff..d68534e7a9 100644
--- a/drivers/tpm/cr50_i2c.c
+++ b/drivers/tpm/cr50_i2c.c
@@ -608,7 +608,7 @@ static int cr50_i2c_ofdata_to_platdata(struct udevice *dev)
priv->irq = irq;
priv->use_irq = true;
} else {
- ret = gpio_request_by_name(dev, "ready-gpio", 0,
+ ret = gpio_request_by_name(dev, "ready-gpios", 0,
&priv->ready_gpio, GPIOD_IS_IN);
if (ret) {
log_warning("Cr50 does not have an ready GPIO/interrupt
(err=%d)\n",
--
2.25.0.341.g760bfbb309-goog
