[U-Boot] [PATCH 26/42] board: freescale: ls1046aqds: support dm_i2c_* API

[Biwen Li]

This supports dm_i2c_* API to
fix compilation error when
enabled CONFIG_DM_I2C as follows:
        - board/freescale/ls1046aqds/built-in.o: In function 
`select_i2c_ch_pca9547:
          board/freescale/ls1046aqds/ls1046aqds.c:276: undefined reference to
          `i2c_write'`

Signed-off-by: Biwen Li <biwen...@nxp.com>
---
 board/freescale/ls1046aqds/ls1046aqds.c | 22 ++++++++++++++++++----
 1 file changed, 18 insertions(+), 4 deletions(-)

diff --git a/board/freescale/ls1046aqds/ls1046aqds.c 
b/board/freescale/ls1046aqds/ls1046aqds.c
index 6ab56279d7..812cbc23d0 100644
--- a/board/freescale/ls1046aqds/ls1046aqds.c
+++ b/board/freescale/ls1046aqds/ls1046aqds.c
@@ -269,11 +269,23 @@ u32 get_lpuart_clk(void)
 }
 #endif
 
-int select_i2c_ch_pca9547(u8 ch)
+int select_i2c_ch_pca9547(u8 ch, int bus_num)
 {
        int ret;
+#ifdef CONFIG_DM_I2C
+       struct udevice *dev;
 
+       ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI,
+                                     1, &dev);
+       if (ret) {
+               printf("%s: Cannot find udev for a bus %d\n", __func__,
+                      bus_num);
+               return ret;
+       }
+       ret = dm_i2c_write(dev, 0, &ch, 1);
+#else
        ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+#endif
        if (ret) {
                puts("PCA: failed to select proper channel\n");
                return ret;
@@ -288,8 +300,10 @@ int dram_init(void)
         * When resuming from deep sleep, the I2C channel may not be
         * in the default channel. So, switch to the default channel
         * before accessing DDR SPD.
+        *
+        * PCA9547 mount on I2C1 bus
         */
-       select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+       select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0);
        fsl_initdram();
 #if (!defined(CONFIG_SPL) && !defined(CONFIG_TFABOOT)) || \
        defined(CONFIG_SPL_BUILD)
@@ -302,7 +316,7 @@ int dram_init(void)
 
 int i2c_multiplexer_select_vid_channel(u8 channel)
 {
-       return select_i2c_ch_pca9547(channel);
+       return select_i2c_ch_pca9547(channel, 0);
 }
 
 int board_early_init_f(void)
@@ -396,7 +410,7 @@ int misc_init_r(void)
 
 int board_init(void)
 {
-       select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+       select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0);
 
 #ifdef CONFIG_SYS_FSL_SERDES
        config_serdes_mux();
-- 
2.17.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot