Hi Frieder,
On 22.10.19 16:24, Schrempf Frieder wrote:
On 22.10.19 15:55, Frieder Schrempf wrote:
Hi Stefan,
On 22.10.19 15:18, Stefan Roese wrote:
Hi Frieder,
Hi Ashish,
Hi Ye Li,
Hi Fabio,
On 18.09.19 09:42, Stefan Roese wrote:
Hi Frieder,
On 18.09.19 09:08, Schrempf Frieder wrote:
<snip>
One further update on this QSPI driver. This driver only works when
loaded via "imx_usb" on the i.MX6ULL EVK. When programmed into QSPI
and booted from QSPI this driver does not detect the SPI NOR
flash:
=> sf probe
unrecognized JEDEC id bytes: ff, ff, ff
Do you have any idea what might explain this difference. I would have
expected that when booting via QSPI it would be "easier" for the
driver, as the BootROM already initializes the QSPI interface. Which
is not the case in the boot via serial download (imx_usb) mode. Here
everyhting (pinmux, clocks, etc) need to be configured.
My feeling is that something is configured "incorrectly" by the
BootROM in this case which is not re-configured as the QSPI driver
needs it to be currently.
Do you have any ideas on what might be the problem here? Is there
something that I can do to help test this? Would it help if I would
send the debug logging of the driver?
I have a strong suspicion of what goes wrong in your case. We
experienced exactly the same issue recently on i.MX6ULL. For some
reasons (I guess differences in BootROM) this does not happen on
i.MX6UL.
The problem is, that the BootROM sets the TDH bits in the
QuadSPI_FLSHCR
register to '01' in case it uses the DDR mode. Afterwards when
U-Boot or
Linux try to access the flash in SDR mode, they fail as the TDH bits
are
still set. Resetting them to '00' solves the problem.
Unfortunately the TDH bits are not documented in the manual of the
i.MX6UL/ULL, but they can be found in the manual of the i.MX7.
For the QSPI driver, this means it needs a fix to set/reset the TDH
bits
according to the mode that is used (DDR/SDR).
For more details please also look here:
https://community.nxp.com/thread/507260
Perfect. With these bits set to 00 again, booting from QSPI now
works on the EVK. Many thanks for this hint! :)
I'm coming back to this issue, as we now have the new NXP patches
integrated into mainline. Including this one:
7949576664ac "spi: fsl_qspi: Fix DDR mode setting for latest iMX
platforms" >
I've now re-tested current mainline on the i.MX6ULL Eval Kit and QSPI
does not work reliably. This is with CONFIG_SYS_FSL_QSPI_AHB enabled
and disabled. How is QSPI supposed to work on i.MX6ULL/ULZ? Is any
one of you running this current mainline driver successfully on one
any i-MX6ULL/ULZ based board? If yes, what is your configuration here?
I don't have any experience with the current mainline SPI NOR driver.
I had a look and the current mainline driver has 7949576664ac "spi:
fsl_qspi: Fix DDR mode setting for latest iMX platforms", but it still
does not reset the TDH bits during init, in case the BootROM has left
them set, which is the case when booting from QSPI on i.MX6ULL.
Initially for detection the driver does not use DDR, so TDH must be cleared.
I've already "played" with those DDR bits (TDH) in this register -
without success so far.
Let's concentrate on the spi-mem driver instead.
Thanks,
Stefan
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
