Dear All,
after watching this mailing list some days I am not sure if I am right here. But I will give it a try. Here my issue. some years ago ( maybe almost 3 years ) I bought 5 Banana-Pi M3. They were running successfully all over the time. A little bit more than a year ago I replaced these M3 by M64 based on the fact that M64 is a little bit more powerful than M3. I shutdown the M3 and put them into a box. Some days ago I tried to boot one and I had to realize that all 5 of them are dead. I did everything what came in my mind. I replaced the USB power supply, I replaced the cable. I wrote the SD card with a new image, I took also the old image, I wrote to a brand new SD card. Also tried the USB OTG plug for power instead the power jack I used always. But no way to bring it up. It always the same. When I power on all 3 LEDs are going on. First the red, than the other two. On the serial console I can watch the boot process. And after about 4.5 seconds the LEDs are dark, and the console hangs. It's not always at the same boot step. Measuring the current it shows 0 mA power consumption. So it switched off itself. Only unplug/plug from/to power will repeat the boot process until it hangs again. When I hit the return key to stop autoboot I get a prompt and this stays forever. In my opinion it could be that these devices lost some information for a successful boot. There are a lot of errors and information which sounds strange for me ( NOT find the head of uboot, blkcnt should not be 0 ) see full list below. As far as I understand there are also several parameter which can be changed. As I don't have a reference I do not know what should be inside. Another question, these devices have an 'uboot' botton on board. This is normally not used. But I couldn't find a useful information for what it is. I asked my question about dead M3 already in Banana-Pi's forum, but without success. If someone knows a source where I could find help be so kind and let me know. Any help is welcome. // Hans sdcard 0 line count 0 [mmc]: mmc driver ver 2014-8-11 15:06:39 [mmc]: ***Try SD card 0*** [mmc]: SD/MMC Card: 4bit, capacity: 30528MB [mmc]: vendor: Man 001b534d Snr 5090575d [mmc]: product: 00000 [mmc]: revision: 1.0 [mmc]: ***SD/MMC 0 init OK!!!*** sdcard 0 init ok ERROR! NOT find the head of uboot. The size of uboot is 000d8000. sum=ce3ec68c src_sum=ce3ec68c Succeed in loading uboot from sdmmc flash. Ready to disable icache. Jump to secend Boot. [ 0.312] U-Boot 2011.09-rc1-00000-gfe0f876 (May 03 2016 - 13:13:31) Allwinner Technology [ 0.321]version: 2.1.0 normal mode [ 0.401]pmbus: normal or secure os ready [ 0.405]PMU: AXP81X [ 0.407]PMU: AXP81X found bat_vol=0, ratio=100 [ 0.413]PMU: dcdc2 900 [ 0.415]PMU: pll1 1008 Mhz AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz set power on vol to default dcdc1_vol = 3300, onoff=1 dcdc2_vol = 900, onoff=1 dcdc3_vol = 900, onoff=1 dcdc4_vol = 900, onoff=1 dcdc6_vol = 900, onoff=1 aldo1_vol = 1800, onoff=0 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 eldo2_vol = 1800, onoff=0 dldo1_vol = 3300, onoff=0 dldo2_vol = 3300, onoff=0 dldo3_vol = 2500, onoff=1 dldo4_vol = 2800, onoff=0 fldo2_vol = 900, onoff=1 gpio0_vol = 3300, onoff=1 gpio1_vol = 3300, onoff=1 find power_sply to end supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b04, value=0xd, pmu_vol=3300 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b08, value=0xd, pmu_vol=3300 supply=dldo3 axp=axp81x, supply=dldo3, vol=1800 reg addr=0x1c20b0c, value=0x0, pmu_vol=1800 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b10, value=0xd, pmu_vol=3300 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b14, value=0xd, pmu_vol=3300 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b18, value=0xd, pmu_vol=3300 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3300 reg addr=0x1c20b1c, value=0xd, pmu_vol=3300 supply=aldo3 axp=axp81x, supply=aldo3, vol=3000 reg addr=0x1f02f00, value=0xa, pmu_vol=3000 config gpio bias voltage finish vbus not exist no battery, limit to dc ac100 reg 0x00 = 0x101 ac100 reg 0xd0 = 0x0 ac100 reg 0xd1 = 0x0 __446__:(board.c:power_source_init) [AXP81X]:[00]=[35] [AXP81X]:[01]=[10] [AXP81X]:[02]=[02] [AXP81X]:[03]=[51] [AXP81X]:[04]=[00] [AXP81X]:[05]=[00] [AXP81X]:[06]=[00] [AXP81X]:[07]=[00] [AXP81X]:[08]=[00] [AXP81X]:[09]=[00] [AXP81X]:[0A]=[00] [AXP81X]:[0B]=[00] [AXP81X]:[0C]=[00] [AXP81X]:[0D]=[00] [AXP81X]:[0E]=[00] [AXP81X]:[0F]=[0E] [AXP81X]:[10]=[3F] [AXP81X]:[11]=[00] [AXP81X]:[12]=[20] [AXP81X]:[13]=[C8] [AXP81X]:[14]=[08] [AXP81X]:[15]=[1A] [AXP81X]:[16]=[1A] [AXP81X]:[17]=[0B] [AXP81X]:[18]=[15] [AXP81X]:[19]=[00] [AXP81X]:[1A]=[16] [AXP81X]:[1B]=[00] [AXP81X]:[1C]=[0B] [AXP81X]:[1D]=[04] [AXP81X]:[1E]=[00] [AXP81X]:[1F]=[00] [AXP81X]:[20]=[11] [AXP81X]:[21]=[A8] [AXP81X]:[22]=[A8] [AXP81X]:[23]=[A8] [AXP81X]:[24]=[A4] [AXP81X]:[25]=[9E] [AXP81X]:[26]=[A8] [AXP81X]:[27]=[FC] [AXP81X]:[28]=[0B] [AXP81X]:[29]=[0B] [AXP81X]:[2A]=[17] [AXP81X]:[2B]=[00] [AXP81X]:[2C]=[00] [AXP81X]:[2D]=[B0] [AXP81X]:[2E]=[40] [AXP81X]:[2F]=[00] [AXP81X]:[30]=[03] [AXP81X]:[31]=[03] [AXP81X]:[32]=[43] [AXP81X]:[33]=[C8] [AXP81X]:[34]=[45] [AXP81X]:[35]=[83] [AXP81X]:[36]=[59] [AXP81X]:[37]=[00] [AXP81X]:[38]=[A5] [AXP81X]:[39]=[1F] [AXP81X]:[3A]=[85] [AXP81X]:[3B]=[08] [AXP81X]:[3C]=[FC] [AXP81X]:[3D]=[16] [AXP81X]:[3E]=[7C] BPI-M3:[AXP81X]:[3A]=[85] limit to 2500mA fel key old mode run key detect no key found no key input dram_para_set start dram_para_set end [ 0.759]DRAM: 2 GiB relocation Offset is: 75af7000 user_gpio config user_gpio ok gic: normal or no secure os mode script config pll_de to 504 Mhz script config pll_video1 to 297 Mhz Not Found clk pll_video in script enable power vcc-hdmi-18, ret=0 DRV_DISP_Init end [ 0.924]boot_disp.output_disp=1 [ 0.927]boot_disp.output_type=3 [ 0.931]boot_disp.output_mode=5 [ 0.934]fetch script data boot_disp.auto_hpd fail disp1 device type(4) enable attched ok, mgr1<-->device1, type=4, mode=5---- ready to set mode workmode = 0 MMC: 0 [ 0.949][mmc]: mmc driver ver 2015-04-13 14:50:00 [ 0.954][mmc]: get sdc_phy_wipe fail. [ 0.958][mmc]: get sdc0 sdc_erase fail. [ 0.962][mmc]: get sdc_f_max fail,use default 50000000Hz [ 0.967][mmc]: get sdc_ex_dly_used fail,use default dly [ 0.973][mmc]: SUNXI SD/MMC: 0 [ 0.986][mmc]: *Try SD card 0* [ 1.019][mmc]: CID 0x1b534d30 0x30303030 0x10509057 0x5d00fb89 [ 1.024][mmc]: mmc clk 50000000 [ 1.028][mmc]: SD/MMC Card: 4bit, capacity: 30528MB [ 1.033][mmc]: boot0 capacity: 0KB,boot1 capacity: 0KB [ 1.038][mmc]: ***SD/MMC 0 init OK!!!*** [ 1.042][mmc]: erase_grp_size:0x1WrBlk * 0x200 = 0x200 Byte [ 1.048][mmc]: secure_feature 0x0 [ 1.051][mmc]: secure_removal_type 0x0 [ 1.055]sunxi flash init ok out of usb burn from boot: without usb In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:6- -name- -start- -size- boot-res : 1000000 2000000 env : 3000000 1000000 boot : 4000000 1000000 rootfs : 5000000 20000000 klog : 25000000 1000000 UDISK : 26000000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_mmc key 0 recovery key high 10, low 8 cant find fstbt value no misc partition is found to be run cmd=run setargs_mmc boot_normal serial is: 00000000000000000000 mount part name boot-res cant open script.bin, maybe it is not exist WORK_MODE_BOOT board_status_probe [ 1.149]pre sys mode sunxi_bmp_logo_display [ 1.280][mmc]: blkcnt should not be 0 [ 1.299]fetch script data boot_disp.output_disp fail [ 1.304]screen_id =1, screen_width =1280, screen_height =720 [ 1.309]frame buffer address 46400000 [ 1.313]Hit any key to stop autoboot: 0 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
