On 18/10/19 11:43, Parthiban Nallathambi wrote:
> Hello Stefano,
>
> On 10/8/19 10:23 AM, Stefano Babic wrote:
>> On 08/10/19 10:12, Parthiban Nallathambi wrote:
>>> Hi Stefano,
>>>
>>> On 10/7/19 6:06 PM, Stefano Babic wrote:
>>>> Hi Parthiban,
>>>>
>>>> On 23/08/19 18:19, Parthiban Nallathambi wrote:
>>>>> Firmware Configuration Block(FCB) for imx6ul(l) needs to be
>>>>> BCH encoded. This patch depends on [1].
>>>>>
>>>>> [1]: https://patchwork.ozlabs.org/project/uboot/list/?series=113810
>>>>>
>>>>
>>>> Why does it depend on this if it is just defoconfig for a board ?
>>>
>>> The patch series was nandbcb inclusion, but this is already merged in
>>> u-boot.
>>> patchwork query shows only the pending merger now.
>>>
>>> As the nandbcb is already in mainline, this patch should apply fine.
>>
>> Please read the whole e-mail. Issue is not that patch cannot be applied,
>> issue is that it breaks several boards. All i.MX6 boards with NAND -
>> check again:
>>
>>>> Building current source for 1 boards (1 thread, 8 jobs per thread)
>>>> arm: + pfla02
>>>> +arch/arm/mach-imx/built-in.o: In function `encode_bch_ecc':
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:45: undefined reference to `init_bch'
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:75: undefined reference to
>>>> `encode_bch'
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:87: undefined reference to `free_bch'
>>>> +arm-poky-linux-gnueabi-ld.bfd: BFD (GNU Binutils) 2.28.0.20170307
>>>> assertion fail ../../bfd/elf32-arm.c:9512
>>>> +make[1]: *** [u-boot] Error 1
>>>> +make: *** [sub-make] Error 2
>>>> 0 0 1 /1 pfla02
>>
>> The same happens to other boards, too.
>
> I missed this. Will send v3 with conditionally including BCH in source
> as well.
>
ok, thanks !
Stefano
> Thanks,
> Parthiban N
>
>>
>> Best regards,
>> Stefano Babic
>>
>>>
>>> Thanks,
>>> Parthiban N
>>>
>>>>
>>>>> Signed-off-by: Parthiban Nallathambi <p...@denx.de>
>>>>> Acked-by: Shyam Saini <shyam.sa...@amarulasolutions.com>
>>>>> ---
>>>>>
>>>>> Notes:
>>>>> Changes in v2:
>>>>> - use kfree instead of free
>>>>>
>>>>> arch/arm/mach-imx/Kconfig | 1 +
>>>>> arch/arm/mach-imx/cmd_nandbcb.c | 72
>>>>> ++++++++++++++++++++++++++++++++-
>>>>> 2 files changed, 71 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
>>>>> index aeb5493488..175bed601e 100644
>>>>> --- a/arch/arm/mach-imx/Kconfig
>>>>> +++ b/arch/arm/mach-imx/Kconfig
>>>>> @@ -74,6 +74,7 @@ config CMD_HDMIDETECT
>>>>> config CMD_NANDBCB
>>>>> bool "i.MX6 NAND Boot Control Block(BCB) command"
>>>>> depends on NAND && CMD_MTDPARTS
>>>>> + select BCH if MX6UL || MX6ULL
>>>>
>>>> This eems to break all i.MX6 boards (not UL(L)) using NAND. In fact, I
>>>> get these errors:
>>>>
>>>> Building current source for 1 boards (1 thread, 8 jobs per thread)
>>>> arm: + pfla02
>>>> +arch/arm/mach-imx/built-in.o: In function `encode_bch_ecc':
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:45: undefined reference to `init_bch'
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:75: undefined reference to
>>>> `encode_bch'
>>>> +arch/arm/mach-imx/cmd_nandbcb.c:87: undefined reference to `free_bch'
>>>> +arm-poky-linux-gnueabi-ld.bfd: BFD (GNU Binutils) 2.28.0.20170307
>>>> assertion fail ../../bfd/elf32-arm.c:9512
>>>> +make[1]: *** [u-boot] Error 1
>>>> +make: *** [sub-make] Error 2
>>>> 0 0 1 /1 pfla02
>>>>
>>>> Can you check this please ? I temporary remove the patch from -next
>>>> branch.
>>>>
>>>> Best regards,
>>>> Stefano Babic
>>>>
>>>>> default y if ARCH_MX6 && NAND_MXS
>>>>> help
>>>>> Unlike normal 'nand write/erase' commands, this command update
>>>>> diff --git a/arch/arm/mach-imx/cmd_nandbcb.c
>>>>> b/arch/arm/mach-imx/cmd_nandbcb.c
>>>>> index 065b814b2e..e11df401e4 100644
>>>>> --- a/arch/arm/mach-imx/cmd_nandbcb.c
>>>>> +++ b/arch/arm/mach-imx/cmd_nandbcb.c
>>>>> @@ -14,8 +14,10 @@
>>>>> #include <asm/io.h>
>>>>> #include <jffs2/jffs2.h>
>>>>> +#include <linux/bch.h>
>>>>> #include <linux/mtd/mtd.h>
>>>>> +#include <asm/arch/sys_proto.h>
>>>>> #include <asm/mach-imx/imx-nandbcb.h>
>>>>> #include <asm/mach-imx/imximage.cfg>
>>>>> #include <mxs_nand.h>
>>>>> @@ -25,6 +27,66 @@
>>>>> #define BF_VAL(v, bf) (((v) & bf##_MASK) >> bf##_OFFSET)
>>>>> #define GETBIT(v, n) (((v) >> (n)) & 0x1)
>>>>> +static uint8_t reverse_bit(uint8_t b)
>>>>> +{
>>>>> + b = (b & 0xf0) >> 4 | (b & 0x0f) << 4;
>>>>> + b = (b & 0xcc) >> 2 | (b & 0x33) << 2;
>>>>> + b = (b & 0xaa) >> 1 | (b & 0x55) << 1;
>>>>> +
>>>>> + return b;
>>>>> +}
>>>>> +
>>>>> +static void encode_bch_ecc(void *buf, struct fcb_block *fcb, int
>>>>> eccbits)
>>>>> +{
>>>>> + int i, j, m = 13;
>>>>> + int blocksize = 128;
>>>>> + int numblocks = 8;
>>>>> + int ecc_buf_size = (m * eccbits + 7) / 8;
>>>>> + struct bch_control *bch = init_bch(m, eccbits, 0);
>>>>> + u8 *ecc_buf = kzalloc(ecc_buf_size, GFP_KERNEL);
>>>>> + u8 *tmp_buf = kzalloc(blocksize * numblocks, GFP_KERNEL);
>>>>> + u8 *psrc, *pdst;
>>>>> +
>>>>> + /*
>>>>> + * The blocks here are bit aligned. If eccbits is a multiple
>>>>> of 8,
>>>>> + * we just can copy bytes. Otherwiese we must move the blocks to
>>>>> + * the next free bit position.
>>>>> + */
>>>>> + WARN_ON(eccbits % 8);
>>>>> +
>>>>> + memcpy(tmp_buf, fcb, sizeof(*fcb));
>>>>> +
>>>>> + for (i = 0; i < numblocks; i++) {
>>>>> + memset(ecc_buf, 0, ecc_buf_size);
>>>>> + psrc = tmp_buf + i * blocksize;
>>>>> + pdst = buf + i * (blocksize + ecc_buf_size);
>>>>> +
>>>>> + /* copy data byte aligned to destination buf */
>>>>> + memcpy(pdst, psrc, blocksize);
>>>>> +
>>>>> + /*
>>>>> + * imx-kobs use a modified encode_bch which reverse the
>>>>> + * bit order of the data before calculating bch.
>>>>> + * Do this in the buffer and use the bch lib here.
>>>>> + */
>>>>> + for (j = 0; j < blocksize; j++)
>>>>> + psrc[j] = reverse_bit(psrc[j]);
>>>>> +
>>>>> + encode_bch(bch, psrc, blocksize, ecc_buf);
>>>>> +
>>>>> + /* reverse ecc bit */
>>>>> + for (j = 0; j < ecc_buf_size; j++)
>>>>> + ecc_buf[j] = reverse_bit(ecc_buf[j]);
>>>>> +
>>>>> + /* Here eccbuf is byte aligned and we can just copy it */
>>>>> + memcpy(pdst + blocksize, ecc_buf, ecc_buf_size);
>>>>> + }
>>>>> +
>>>>> + kfree(ecc_buf);
>>>>> + kfree(tmp_buf);
>>>>> + free_bch(bch);
>>>>> +}
>>>>> +
>>>>> static u8 calculate_parity_13_8(u8 d)
>>>>> {
>>>>> u8 p = 0;
>>>>> @@ -231,8 +293,14 @@ static int nandbcb_update(struct mtd_info
>>>>> *mtd, loff_t off, size_t size,
>>>>> goto dbbt_data_page_err;
>>>>> }
>>>>> - memcpy(fcb_raw_page + 12, fcb, sizeof(struct fcb_block));
>>>>> - encode_hamming_13_8(fcb_raw_page + 12, fcb_raw_page + 12 +
>>>>> 512, 512);
>>>>> + if (is_mx6ul() || is_mx6ull()) {
>>>>> + /* 40 bit BCH, for i.MX6UL(L) */
>>>>> + encode_bch_ecc(fcb_raw_page + 32, fcb, 40);
>>>>> + } else {
>>>>> + memcpy(fcb_raw_page + 12, fcb, sizeof(struct fcb_block));
>>>>> + encode_hamming_13_8(fcb_raw_page + 12,
>>>>> + fcb_raw_page + 12 + 512, 512);
>>>>> + }
>>>>> /*
>>>>> * Set the first and second byte of OOB data to 0xFF, not
>>>>> 0x00. These
>>>>> * bytes are used as the Manufacturers Bad Block Marker
>>>>> (MBBM). Since
>>>>>
>>>>
>>>>
>>>
>>
>>
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
