On 2019/7/16 下午7:57, Jagan Teki wrote:
Configure PHY RX_CM_INPUT for lpddr4 during phy IO config.
Signed-off-by: Jagan Teki <[email protected]>
Signed-off-by: YouMin Chen <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Thanks,
- Kever
---
drivers/ram/rockchip/sdram_rk3399.c | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
diff --git a/drivers/ram/rockchip/sdram_rk3399.c
b/drivers/ram/rockchip/sdram_rk3399.c
index c02f936f2a..2ab10da53f 100644
--- a/drivers/ram/rockchip/sdram_rk3399.c
+++ b/drivers/ram/rockchip/sdram_rk3399.c
@@ -39,6 +39,7 @@
#define PHY_BOOSTN_EN 0x1
#define PHY_SLEWP_EN 0x1
#define PHY_SLEWN_EN 0x1
+#define PHY_RX_CM_INPUT 0x1
#define CRU_SFTRST_DDR_CTRL(ch, n) ((0x1 << (8 + 16 + (ch) * 4)) | \
((n) << (8 + (ch) * 4)))
@@ -384,6 +385,27 @@ static int phy_io_config(const struct chan_info *chan,
/* PHY_939 PHY_PAD_CS_DRIVE */
clrsetbits_le32(&denali_phy[939], 0x3 << 17, speed << 17);
+ if (IS_ENABLED(CONFIG_RAM_RK3399_LPDDR4)) {
+ /* RX_CM_INPUT */
+ reg_value = PHY_RX_CM_INPUT;
+ /* PHY_924 PHY_PAD_FDBK_DRIVE */
+ clrsetbits_le32(&denali_phy[924], 0x1 << 14, reg_value << 14);
+ /* PHY_926 PHY_PAD_DATA_DRIVE */
+ clrsetbits_le32(&denali_phy[926], 0x1 << 11, reg_value << 11);
+ /* PHY_927 PHY_PAD_DQS_DRIVE */
+ clrsetbits_le32(&denali_phy[927], 0x1 << 13, reg_value << 13);
+ /* PHY_928 PHY_PAD_ADDR_DRIVE */
+ clrsetbits_le32(&denali_phy[928], 0x1 << 19, reg_value << 19);
+ /* PHY_929 PHY_PAD_CLK_DRIVE */
+ clrsetbits_le32(&denali_phy[929], 0x1 << 21, reg_value << 21);
+ /* PHY_935 PHY_PAD_CKE_DRIVE */
+ clrsetbits_le32(&denali_phy[935], 0x1 << 19, reg_value << 19);
+ /* PHY_937 PHY_PAD_RST_DRIVE */
+ clrsetbits_le32(&denali_phy[937], 0x1 << 19, reg_value << 19);
+ /* PHY_939 PHY_PAD_CS_DRIVE */
+ clrsetbits_le32(&denali_phy[939], 0x1 << 19, reg_value << 19);
+ }
+
return 0;
}
_______________________________________________
U-Boot mailing list
[email protected]
https://lists.denx.de/listinfo/u-boot
