Hi,Alex I have already sent the patch set of ls1028aqds i2c dm. Please check the patchwork link below： https://patchwork.ozlabs.org/project/uboot/list/?series=118709
thanks, Chaunhua > -----Original Message----- > From: Alex Marginean <alexandru.margin...@nxp.com> > Sent: 2019年7月12日 19:23 > To: u-boot@lists.denx.de > Cc: Chuanhua Han <chuanhua....@nxp.com>; Prabhakar Kushwaha > <prabhakar.kushw...@nxp.com>; Alex Marginean <alexm.ossl...@gmail.com> > Subject: [PATCH 2/2] configs: ls1028aqds: enable I2C and GPIO DM > > LS1028A was already converted to I2C/GPIO DM, move the QDS board over too. > > Signed-off-by: Alex Marginean <alexm.ossl...@gmail.com> > --- > configs/ls1028aqds_tfa_SECURE_BOOT_defconfig | 5 ++++- > configs/ls1028aqds_tfa_defconfig | 5 ++++- > 2 files changed, 8 insertions(+), 2 deletions(-) > > diff --git a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig > b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig > index 4a2b354008..76c9af5ef3 100644 > --- a/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig > +++ b/configs/ls1028aqds_tfa_SECURE_BOOT_defconfig > @@ -1,5 +1,6 @@ > CONFIG_ARM=y > CONFIG_TARGET_LS1028AQDS=y > +CONFIG_SYS_MALLOC_F_LEN=0x6000 > CONFIG_SECURE_BOOT=y > CONFIG_SYS_FSL_SDHC_CLK_DIV=1 > CONFIG_TFABOOT=y > @@ -8,7 +9,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y > CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y > CONFIG_AHCI=y > CONFIG_DISTRO_DEFAULTS=y > -# CONFIG_SYS_MALLOC_F is not set > CONFIG_FIT_VERBOSE=y > CONFIG_OF_BOARD_SETUP=y > CONFIG_OF_STDOUT_VIA_ALIAS=y > @@ -31,6 +31,9 @@ CONFIG_NETCONSOLE=y > CONFIG_DM=y > CONFIG_SCSI_AHCI=y > CONFIG_SATA_CEVA=y > +CONFIG_DM_GPIO=y > +CONFIG_DM_I2C=y > +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y > CONFIG_DM_MMC=y > CONFIG_FSL_ESDHC=y > CONFIG_DM_SPI_FLASH=y > diff --git a/configs/ls1028aqds_tfa_defconfig > b/configs/ls1028aqds_tfa_defconfig > index b315910414..7c98474d73 100644 > --- a/configs/ls1028aqds_tfa_defconfig > +++ b/configs/ls1028aqds_tfa_defconfig > @@ -1,5 +1,6 @@ > CONFIG_ARM=y > CONFIG_TARGET_LS1028AQDS=y > +CONFIG_SYS_MALLOC_F_LEN=0x6000 > CONFIG_SYS_FSL_SDHC_CLK_DIV=1 > CONFIG_TFABOOT=y > CONFIG_NR_DRAM_BANKS=2 > @@ -7,7 +8,6 @@ CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y > CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y > CONFIG_AHCI=y > CONFIG_DISTRO_DEFAULTS=y > -# CONFIG_SYS_MALLOC_F is not set > CONFIG_FIT_VERBOSE=y > CONFIG_OF_BOARD_SETUP=y > CONFIG_OF_STDOUT_VIA_ALIAS=y > @@ -34,6 +34,9 @@ CONFIG_DM=y > CONFIG_SCSI_AHCI=y > CONFIG_SATA_CEVA=y > CONFIG_FSL_CAAM=y > +CONFIG_DM_GPIO=y > +CONFIG_DM_I2C=y > +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y > CONFIG_DM_MMC=y > CONFIG_FSL_ESDHC=y > CONFIG_DM_SPI_FLASH=y > -- > 2.17.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
