CTL 145, 146, 159, 160 registers are used to configure
soc odt on rk3399.
These soc odt values are updated from CS0_MR22_VAL and
CS1_MR22_VAL and for lpddr4 these values ORed with
tsel_rd_select_n.
Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
Signed-off-by: YouMin Chen <c...@rock-chips.com>
---
drivers/ram/rockchip/sdram_rk3399.c | 49 ++++++++++++++++++++++++++++-
1 file changed, 48 insertions(+), 1 deletion(-)
diff --git a/drivers/ram/rockchip/sdram_rk3399.c
b/drivers/ram/rockchip/sdram_rk3399.c
index caf8180018..5f118fc0c6 100644
--- a/drivers/ram/rockchip/sdram_rk3399.c
+++ b/drivers/ram/rockchip/sdram_rk3399.c
@@ -40,6 +40,8 @@
#define PHY_SLEWP_EN 0x1
#define PHY_SLEWN_EN 0x1
#define PHY_RX_CM_INPUT 0x1
+#define CS0_MR22_VAL 0
+#define CS1_MR22_VAL 3
#define CRU_SFTRST_DDR_CTRL(ch, n) ((0x1 << (8 + 16 + (ch) * 4)) | \
((n) << (8 + (ch) * 4)))
@@ -554,7 +556,7 @@ static void set_ds_odt(const struct chan_info *chan,
const struct rk3399_sdram_params *params, u32 mr5)
{
u32 *denali_phy = chan->publ->denali_phy;
-
+ u32 *denali_ctl = chan->pctl->denali_ctl;
u32 tsel_idle_en, tsel_wr_en, tsel_rd_en;
u32 tsel_idle_select_p, tsel_rd_select_p;
u32 tsel_idle_select_n, tsel_rd_select_n;
@@ -562,6 +564,7 @@ static void set_ds_odt(const struct chan_info *chan,
u32 tsel_wr_select_dq_n, tsel_wr_select_ca_n;
u32 tsel_ckcs_select_p, tsel_ckcs_select_n;
struct io_setting *io = NULL;
+ u32 soc_odt = 0;
u32 reg_value;
if (params->base.dramtype == LPDDR4) {
@@ -581,6 +584,35 @@ static void set_ds_odt(const struct chan_info *chan,
tsel_ckcs_select_p = io->wr_ckcs_drv;
tsel_ckcs_select_n = PHY_DRV_ODT_34_3;
+ switch (tsel_rd_select_n) {
+ case PHY_DRV_ODT_240:
+ soc_odt = 1;
+ break;
+ case PHY_DRV_ODT_120:
+ soc_odt = 2;
+ break;
+ case PHY_DRV_ODT_80:
+ soc_odt = 3;
+ break;
+ case PHY_DRV_ODT_60:
+ soc_odt = 4;
+ break;
+ case PHY_DRV_ODT_48:
+ soc_odt = 5;
+ break;
+ case PHY_DRV_ODT_40:
+ soc_odt = 6;
+ break;
+ case PHY_DRV_ODT_34_3:
+ soc_odt = 6;
+ printf("%s: Unable to support LPDDR4 MR22 Soc ODT\n",
+ __func__);
+ break;
+ case PHY_DRV_ODT_HI_Z:
+ default:
+ soc_odt = 0;
+ break;
+ }
} else if (params->base.dramtype == LPDDR3) {
tsel_rd_select_p = PHY_DRV_ODT_240;
tsel_rd_select_n = PHY_DRV_ODT_HI_Z;
@@ -621,6 +653,21 @@ static void set_ds_odt(const struct chan_info *chan,
tsel_wr_en = 0;
tsel_idle_en = 0;
+ /* F0_0 */
+ clrsetbits_le32(&denali_ctl[145], 0xFF << 16,
+ (soc_odt | (CS0_MR22_VAL << 3)) << 16);
+ /* F2_0, F1_0 */
+ clrsetbits_le32(&denali_ctl[146], 0xFF00FF,
+ ((soc_odt | (CS0_MR22_VAL << 3)) << 16) |
+ (soc_odt | (CS0_MR22_VAL << 3)));
+ /* F0_1 */
+ clrsetbits_le32(&denali_ctl[159], 0xFF << 16,
+ (soc_odt | (CS1_MR22_VAL << 3)) << 16);
+ /* F2_1, F1_1 */
+ clrsetbits_le32(&denali_ctl[160], 0xFF00FF,
+ ((soc_odt | (CS1_MR22_VAL << 3)) << 16) |
+ (soc_odt | (CS1_MR22_VAL << 3)));
+
/*
* phy_dq_tsel_select_X 24bits DENALI_PHY_6/134/262/390 offset_0
* sets termination values for read/idle cycles and drive strength
--
2.18.0.321.gffc6fa0e3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
