On Sun, May 26, 2019 at 04:52:32PM +0200, Code Kipper wrote:
> On Sun, 26 May 2019 at 14:13, Jernej Škrabec <jernej.skra...@gmail.com> wrote:
> >
> > Hi!
> >
> > Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekip...@gmail.com
> > napisal(a):
> > > From: Marcus Cooper <codekip...@gmail.com>
> > >
> > > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> > > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> > > SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> > > dual colour LED and an optical S/PDIF connector.
> > >
> > > Signed-off-by: Marcus Cooper <codekip...@gmail.com>
> > > ---
> > > Changes in v4:
> > > - updated dts to reflex current linux kernel status
> > >
> > > Changes in v3:
> > > - Removed incorrect commit author
> > > - Included v1-v2 change info
> > >
> > > Changes in v2:
> > > - updated dts to reflex current linux kernel status
> > > ---
> > > arch/arm/dts/Makefile | 1 +
> > > arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
> > > board/sunxi/MAINTAINERS | 5 +
> > > configs/beelink_x2_defconfig | 19 +++
> > > 4 files changed, 241 insertions(+)
> > > create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> > > create mode 100644 configs/beelink_x2_defconfig
> > >
> > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > > index 83058c4452..716108dd2e 100644
> > > --- a/arch/arm/dts/Makefile
> > > +++ b/arch/arm/dts/Makefile
> > > @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
> > > sun8i-h2-plus-orangepi-r1.dtb \
> > > sun8i-h2-plus-orangepi-zero.dtb \
> > > sun8i-h3-bananapi-m2-plus.dtb \
> > > + sun8i-h3-beelink-x2.dtb \
> > > sun8i-h3-libretech-all-h3-cc.dtb \
> > > sun8i-h3-nanopi-m1.dtb \
> > > sun8i-h3-nanopi-m1-plus.dtb \
> > > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > > b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> > > index 0000000000..25540b7694
> > > --- /dev/null
> > > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > > @@ -0,0 +1,216 @@
> > > +/*
> > > + * Copyright (C) 2017 Marcus Cooper <codekip...@gmail.com>
> > > + *
> > > + * This file is dual-licensed: you can use it either under the terms
> > > + * of the GPL or the X11 license, at your option. Note that this dual
> > > + * licensing only applies to this file, and not this project as a
> > > + * whole.
> > > + *
> > > + * a) This file is free software; you can redistribute it and/or
> > > + * modify it under the terms of the GNU General Public License as
> > > + * published by the Free Software Foundation; either version 2 of the
> > > + * License, or (at your option) any later version.
> > > + *
> > > + * This file is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > + * GNU General Public License for more details.
> > > + *
> > > + * Or, alternatively,
> > > + *
> > > + * b) Permission is hereby granted, free of charge, to any person
> > > + * obtaining a copy of this software and associated documentation
> > > + * files (the "Software"), to deal in the Software without
> > > + * restriction, including without limitation the rights to use,
> > > + * copy, modify, merge, publish, distribute, sublicense, and/or
> > > + * sell copies of the Software, and to permit persons to whom the
> > > + * Software is furnished to do so, subject to the following
> > > + * conditions:
> > > + *
> > > + * The above copyright notice and this permission notice shall be
> > > + * included in all copies or substantial portions of the Software.
> > > + *
> > > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > > + * OTHER DEALINGS IN THE SOFTWARE.
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "sun8i-h3.dtsi"
> > > +#include "sunxi-common-regulators.dtsi"
> > > +
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/input/input.h>
> > > +
> > > +/ {
> > > + model = "Beelink X2";
> > > + compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> > > +
> > > + aliases {
> > > + serial0 = &uart0;
> > > + ethernet0 = &emac;
> > > + ethernet1 = &sdiowifi;
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +
> > > + connector {
> > > + compatible = "hdmi-connector";
> > > + type = "a";
> > > +
> > > + port {
> > > + hdmi_con_in: endpoint {
> > > + remote-endpoint = <&hdmi_out_con>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + leds {
> > > + compatible = "gpio-leds";
> > > +
> > > + blue {
> > > + label = "beelink-x2:blue:pwr";
> > > + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /*
> > PL10 */
> > > + default-state = "on";
> > > + };
> > > +
> > > + red {
> > > + label = "beelink-x2:red:standby";
> > > + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15
> > */
> > > + };
> > > + };
> > > +
> > > + wifi_pwrseq: wifi_pwrseq {
> > > + compatible = "mmc-pwrseq-simple";
> > > + reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > > + };
> > > +
> > > + sound_spdif {
> > > + compatible = "simple-audio-card";
> > > + simple-audio-card,name = "On-board SPDIF";
> > > +
> > > + simple-audio-card,cpu {
> > > + sound-dai = <&spdif>;
> > > + };
> > > +
> > > + simple-audio-card,codec {
> > > + sound-dai = <&spdif_out>;
> > > + };
> > > + };
> > > +
> > > + spdif_out: spdif-out {
> > > + #sound-dai-cells = <0>;
> > > + compatible = "linux,spdif-dit";
> > > + };
> > > +};
> > > +
> > > +&de {
> > > + status = "okay";
> > > +};
> > > +
> > > +&ehci0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&ehci1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&emac {
> > > + phy-handle = <&int_mii_phy>;
> > > + phy-mode = "mii";
> > > + allwinner,leds-active-low;
> > > + status = "okay";
> > > +};
> > > +
> > > +&hdmi {
> > > + status = "okay";
> > > +};
> > > +
> > > +&hdmi_out {
> > > + hdmi_out_con: endpoint {
> > > + remote-endpoint = <&hdmi_con_in>;
> > > + };
> > > +};
> > > +
> > > +&ir {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&ir_pins_a>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&mmc0 {
> > > + vmmc-supply = <®_vcc3v3>;
> > > + bus-width = <4>;
> > > + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > > + status = "okay";
> > > +};
> > > +
> > > +&mmc1 {
> > > + vmmc-supply = <®_vcc3v3>;
> > > + bus-width = <4>;
> > > + non-removable;
> > > + status = "okay";
> > > +
> > > + /*
> > > + * Explicitly define the sdio device, so that we can add an ethernet
> > > + * alias for it (which e.g. makes u-boot set a mac-address).
> > > + */
> > > + sdiowifi: sdio_wifi@1 {
> > > + reg = <1>;
> > > + };
> > > +};
> > > +
> > > +&mmc2 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc2_8bit_pins>;
> > > + vmmc-supply = <®_vcc3v3>;
> > > + bus-width = <8>;
> > > + non-removable;
> > > + cap-mmc-hw-reset;
> > > + status = "okay";
> > > +};
> > > +
> > > +&ohci0 {
> > > + status = "okay";
> > > +};
> > > +
> > > +&ohci1 {
> > > + status = "okay";
> > > +};
> > > +
> > > +®_usb0_vbus {
> > > + gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > > + status = "okay";
> > > +};
> > > +
> > > +&spdif {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&spdif_tx_pins_a>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&uart0 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&uart0_pins_a>;
> > > + status = "okay";
> > > +};
> > > +
> > > +&usb_otg {
> > > + dr_mode = "otg";
> > > + status = "okay";
> > > +};
> > > +
> > > +&usbphy {
> > > + /* USB VBUS is always on except for the OTG port */
> > > + status = "okay";
> > > + usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> > > + usb0_vbus-supply = <®_usb0_vbus>;
> > > +};
> > > diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> > > index bdd1854197..28f2bece40 100644
> > > --- a/board/sunxi/MAINTAINERS
> > > +++ b/board/sunxi/MAINTAINERS
> > > @@ -172,6 +172,11 @@ S: Maintained
> > > F: configs/beelink_gs1_defconfig
> > > F: arch/arm/dts/sun50i-h6-beelink-gs1.dts
> > >
> > > +BEELINK X2 BOARD
> > > +M: Marcus Cooper <codekip...@gmail.com>
> > > +S: Maintained
> > > +F: configs/beelink_x2_defconfig
> > > +
> > > COLOMBUS BOARD
> > > M: Maxime Ripard <maxime.rip...@bootlin.com>
> > > S: Maintained
> > > diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> > > new file mode 100644
> > > index 0000000000..6508e470a0
> > > --- /dev/null
> > > +++ b/configs/beelink_x2_defconfig
> > > @@ -0,0 +1,19 @@
> > > +CONFIG_ARM=y
> > > +CONFIG_ARCH_SUNXI=y
> > > +CONFIG_SPL=y
> > > +CONFIG_MACH_SUN8I_H3=y
> > > +CONFIG_DRAM_CLK=624
> > > +CONFIG_DRAM_ZQ=3881979
> > > +CONFIG_DRAM_ODT_EN=y
> > > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> > > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > > +CONFIG_CONSOLE_MUX=y
> > > +CONFIG_SPL_I2C_SUPPORT=y
> > > +# CONFIG_CMD_FLASH is not set
> > > +# CONFIG_SPL_DOS_PARTITION is not set
> > > +# CONFIG_SPL_EFI_PARTITION is not set
> > > +CONFIG_SUN8I_EMAC=y
> > > +CONFIG_SY8106A_POWER=y
> > > +CONFIG_USB_EHCI_HCD=y
> > > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
> >
> > I think you should add:
> > CONFIG_SPL_TEXT_BASE=0x60
> >
> > due to following commit:
> > http://git.denx.de/?p=u-boot/u-boot-sunxi.git;a=commit;h=f89d6133ee
> ACK, arrgghh I thought the sunxi-next branch was misbehaving. Now
> boots ontop of master,Can we make that a default in Kconfig instead of having to put it in pretty much every defconfig? Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
signature.asc
Description: PGP signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
