Hi, -----Original Message----- From: Marek Vasut [mailto:ma...@denx.de] Sent: Tuesday, May 21, 2019 6:14 PM To: Siva Durga Prasad Paladugu <siva...@xilinx.com>; Jean-Jacques Hiblot <jjhib...@ti.com>; lu...@denx.de Cc: Marcel Ziswiler <marcel.ziswi...@toradex.com>; u-boot@lists.denx.de; Miquel Raynal <miquel.ray...@bootlin.com>; Stefan Roese <s...@denx.de>; Tom Rini <tr...@konsulko.com>; Ryder Lee <ryder....@mediatek.com>; Heinrich Schuchardt <xypron.g...@gmx.de>; Michal Simek <mich...@xilinx.com>; Krzysztof Kozlowski <k...@kernel.org>; Maxime Ripard <maxime.rip...@bootlin.com>; Sven Schwermer <s...@svenschwermer.de>; Ramon Fried <ramon.fr...@gmail.com>; Eugeniu Rosca <roscaeuge...@gmail.com>; Vitaly Andrianov <vita...@ti.com>; Joe Hershberger <joe.hershber...@ni.com>; Tom Warren <twar...@nvidia.com> Subject: Re: [U-Boot] [PATCH v2 00/18] Improvement for the DWC3 USB generic driver and fixes for the K2 platforms
On 5/21/19 1:36 PM, Siva Durga Prasad Paladugu wrote: > Hi, Hi, > Tested the series with one out of tree > patch(https://marc.info/?l=u-boot&m=155409909828219 ) on Xilinx ZynqMP and it > looks fine. > We may need to finalize on https://marc.info/?l=u-boot&m=155409909828219 as > well. > > U-Boot 2019.04-rc4-00065-g5063fa3-dirty (May 21 2019 - 16:58:34 +0530) Does it still work on current master (2019.07-rc) ? Testing a patch on top of rc version of previous release is not really helpful. [...] Its same with latest too. U-Boot 2019.07-rc2-00182-g29792e4-dirty (May 22 2019 - 11:21:25 +0530) Model: ZynqMP ZCU102 Rev1.0 Board: Xilinx ZynqMP DRAM: 4 GiB EL Level: EL2 Chip ID: zu9eg MMC: mmc@ff170000: 0 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial@ff000000 Out: serial@ff000000 Err: serial@ff000000 Bootmode: JTAG_MODE Reset reason: EXTERNAL Net: ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id Warning: ethernet@ff0e0000 (eth0) using random MAC address - ca:f4:c2:4a:b8:df eth0: ethernet@ff0e0000 Hit any key to stop autoboot: 0 ZynqMP> usb start starting USB... Bus dwc3@fe200000: Register 2000440 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus dwc3@fe200000 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found ZynqMP> ls ubs 0 ZynqMP> ls usb 0 5242880 dummy.bin 133849600 Image 2 file(s), 0 dir(s) ZynqMP> load usb 0 100000 dummy.bin 5242880 bytes read in 55 ms (90.9 MiB/s) ZynqMP> Thanks, Siva -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
