czw., 9 maj 2019 o 20:48 Joe Hershberger <joe.hershber...@ni.com> napisał(a): > > On Tue, Apr 30, 2019 at 11:04 AM Bartosz Golaszewski <b...@bgdev.pl> wrote: > > > > From: Bartosz Golaszewski <bgolaszew...@baylibre.com> > > > > Add support for CONFIG_DM_ETH to the davinci_emac driver. Optimally > > we should only support DM-enabled platforms but there are several > > non-DT boards that still use it so either we need to keep supporting > > it or drop the boards from u-boot. For now we're stuck with ugly > > ifdefs. > > Which boards are still not using DM that you refer to here? >
The following configs define CONFIG_DRIVER_TI_EMAC=y and don't define CONFIG_DM=y: am3517_evm_defconfig calimain_defconfig cm_t3517_defconfig ea20_defconfig eco5pk_defconfig ipam390_defconfig mcx_defconfig mt_ventoux_defconfig twister_defconfig Are these still maintained? Best regards, Bartosz Golaszewski > > > > This patch adds support for driver-model to the driver and converts > > all platforms that use the driver model to selecting CONFIG_DM_ETH. > > > > Tested on da850-evm and da850-lcdk. > > > > Signed-off-by: Bartosz Golaszewski <bgolaszew...@baylibre.com> > > --- > > NOTE: I'm currently working on modernizing da850 support in u-boot. > > This patch is just the first step - I plan on improving the emac driver > > in general but I'll be OoO until end of next week, so I decided to post > > it already for reviews. > > > > Does anyone know what the status is on boards like twister, ea20 etc. > > that use davinci_emac, but don't use the driver model? Dropping them > > would make it easier to clean up this driver. > > > > This patch applies on top of my previous series[1]. > > > > [1] https://lists.denx.de/pipermail/u-boot/2019-April/367236.html > > > > arch/arm/mach-davinci/cpu.c | 13 --- > > arch/arm/mach-omap2/omap3/emac.c | 3 +- > > board/davinci/da8xxevm/da850evm.c | 5 -- > > board/davinci/da8xxevm/omapl138_lcdk.c | 14 ---- > > board/logicpd/am3517evm/am3517evm.c | 1 - > > board/ti/ti816x/evm.c | 3 +- > > configs/am3517_evm_defconfig | 1 + > > configs/da850_am18xxevm_defconfig | 1 + > > configs/da850evm_defconfig | 1 + > > configs/da850evm_direct_nor_defconfig | 1 + > > configs/omapl138_lcdk_defconfig | 1 + > > configs/ti816x_evm_defconfig | 1 + > > drivers/net/ti/davinci_emac.c | 109 +++++++++++++++++++++---- > > 13 files changed, 100 insertions(+), 54 deletions(-) > > > > diff --git a/arch/arm/mach-davinci/cpu.c b/arch/arm/mach-davinci/cpu.c > > index f97ad3fc74..9fd6564d04 100644 > > --- a/arch/arm/mach-davinci/cpu.c > > +++ b/arch/arm/mach-davinci/cpu.c > > @@ -5,7 +5,6 @@ > > */ > > > > #include <common.h> > > -#include <netdev.h> > > #include <asm/arch/hardware.h> > > #include <asm/io.h> > > > > @@ -90,15 +89,3 @@ int set_cpu_clk_info(void) > > gd->bd->bi_dsp_freq = 0; > > return 0; > > } > > - > > -/* > > - * Initializes on-chip ethernet controllers. > > - * to override, implement board_eth_init() > > - */ > > -int cpu_eth_init(bd_t *bis) > > -{ > > -#if defined(CONFIG_DRIVER_TI_EMAC) > > - davinci_emac_initialize(); > > -#endif > > - return 0; > > -} > > diff --git a/arch/arm/mach-omap2/omap3/emac.c > > b/arch/arm/mach-omap2/omap3/emac.c > > index c79e870183..fb0c9188f5 100644 > > --- a/arch/arm/mach-omap2/omap3/emac.c > > +++ b/arch/arm/mach-omap2/omap3/emac.c > > @@ -7,7 +7,6 @@ > > */ > > > > #include <common.h> > > -#include <netdev.h> > > #include <asm/io.h> > > #include <asm/arch/am35x_def.h> > > > > @@ -24,5 +23,5 @@ int cpu_eth_init(bd_t *bis) > > reset &= ~CPGMACSS_SW_RST; > > writel(reset, &am35x_scm_general_regs->ip_sw_reset); > > > > - return davinci_emac_initialize(); > > + return 0; > > } > > diff --git a/board/davinci/da8xxevm/da850evm.c > > b/board/davinci/da8xxevm/da850evm.c > > index 1bc26828bf..0d2bc5fb32 100644 > > --- a/board/davinci/da8xxevm/da850evm.c > > +++ b/board/davinci/da8xxevm/da850evm.c > > @@ -13,7 +13,6 @@ > > #include <environment.h> > > #include <i2c.h> > > #include <net.h> > > -#include <netdev.h> > > #include <spi.h> > > #include <spi_flash.h> > > #include <asm/arch/hardware.h> > > @@ -472,10 +471,6 @@ int board_eth_init(bd_t *bis) > > if (rmii_hw_init()) > > printf("RMII hardware init failed!!!\n"); > > #endif > > - if (!davinci_emac_initialize()) { > > - printf("Error: Ethernet init failed!\n"); > > - return -1; > > - } > > > > return 0; > > } > > diff --git a/board/davinci/da8xxevm/omapl138_lcdk.c > > b/board/davinci/da8xxevm/omapl138_lcdk.c > > index 2c2f885d43..ef9656add8 100644 > > --- a/board/davinci/da8xxevm/omapl138_lcdk.c > > +++ b/board/davinci/da8xxevm/omapl138_lcdk.c > > @@ -11,7 +11,6 @@ > > #include <common.h> > > #include <i2c.h> > > #include <net.h> > > -#include <netdev.h> > > #include <spi.h> > > #include <spi_flash.h> > > #include <asm/arch/hardware.h> > > @@ -229,19 +228,6 @@ int board_init(void) > > > > #ifdef CONFIG_DRIVER_TI_EMAC > > > > -/* > > - * Initializes on-board ethernet controllers. > > - */ > > -int board_eth_init(bd_t *bis) > > -{ > > - if (!davinci_emac_initialize()) { > > - printf("Error: Ethernet init failed!\n"); > > - return -1; > > - } > > - > > - return 0; > > -} > > - > > #endif /* CONFIG_DRIVER_TI_EMAC */ > > > > #define CFG_MAC_ADDR_SPI_BUS 0 > > diff --git a/board/logicpd/am3517evm/am3517evm.c > > b/board/logicpd/am3517evm/am3517evm.c > > index 10031a4801..bfd4e78274 100644 > > --- a/board/logicpd/am3517evm/am3517evm.c > > +++ b/board/logicpd/am3517evm/am3517evm.c > > @@ -28,7 +28,6 @@ > > #include <linux/usb/gadget.h> > > #include <linux/usb/musb.h> > > #include <i2c.h> > > -#include <netdev.h> > > #include "am3517evm.h" > > > > DECLARE_GLOBAL_DATA_PTR; > > diff --git a/board/ti/ti816x/evm.c b/board/ti/ti816x/evm.c > > index 07a084bab8..240df8cbe1 100644 > > --- a/board/ti/ti816x/evm.c > > +++ b/board/ti/ti816x/evm.c > > @@ -9,7 +9,6 @@ > > #include <common.h> > > #include <environment.h> > > #include <spl.h> > > -#include <netdev.h> > > #include <asm/cache.h> > > #include <asm/io.h> > > #include <asm/arch/clock.h> > > @@ -56,7 +55,7 @@ int board_eth_init(bd_t *bis) > > printf("Unable to read MAC address. Set > > <ethaddr>\n"); > > } > > > > - return davinci_emac_initialize(); > > + return 0; > > } > > > > #ifdef CONFIG_SPL_BUILD > > diff --git a/configs/am3517_evm_defconfig b/configs/am3517_evm_defconfig > > index b9f59f3291..0ea28a20b2 100644 > > --- a/configs/am3517_evm_defconfig > > +++ b/configs/am3517_evm_defconfig > > @@ -45,6 +45,7 @@ CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y > > CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 > > CONFIG_SPL_NAND_SIMPLE=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_PINCTRL=y > > CONFIG_PINCTRL_SINGLE=y > > diff --git a/configs/da850_am18xxevm_defconfig > > b/configs/da850_am18xxevm_defconfig > > index f098222113..6227cafc90 100644 > > --- a/configs/da850_am18xxevm_defconfig > > +++ b/configs/da850_am18xxevm_defconfig > > @@ -52,6 +52,7 @@ CONFIG_SPI_FLASH=y > > CONFIG_SPI_FLASH_STMICRO=y > > CONFIG_SPI_FLASH_WINBOND=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_DM_SERIAL=y > > CONFIG_SYS_NS16550=y > > diff --git a/configs/da850evm_defconfig b/configs/da850evm_defconfig > > index 221c204af0..78eadc6330 100644 > > --- a/configs/da850evm_defconfig > > +++ b/configs/da850evm_defconfig > > @@ -60,6 +60,7 @@ CONFIG_SPI_FLASH_STMICRO=y > > CONFIG_SPI_FLASH_WINBOND=y > > CONFIG_SPI_FLASH_MTD=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_PINCTRL=y > > CONFIG_PINCTRL_SINGLE=y > > diff --git a/configs/da850evm_direct_nor_defconfig > > b/configs/da850evm_direct_nor_defconfig > > index 166e77b8e3..2dd82d68b9 100644 > > --- a/configs/da850evm_direct_nor_defconfig > > +++ b/configs/da850evm_direct_nor_defconfig > > @@ -51,6 +51,7 @@ CONFIG_SPI_FLASH=y > > CONFIG_SPI_FLASH_STMICRO=y > > CONFIG_SPI_FLASH_WINBOND=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_PINCTRL=y > > CONFIG_PINCTRL_SINGLE=y > > diff --git a/configs/omapl138_lcdk_defconfig > > b/configs/omapl138_lcdk_defconfig > > index e43141844a..0600ac3f4a 100644 > > --- a/configs/omapl138_lcdk_defconfig > > +++ b/configs/omapl138_lcdk_defconfig > > @@ -51,6 +51,7 @@ CONFIG_SF_DEFAULT_SPEED=30000000 > > CONFIG_SPI_FLASH_STMICRO=y > > CONFIG_SPI_FLASH_WINBOND=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_DM_SERIAL=y > > CONFIG_SYS_NS16550=y > > diff --git a/configs/ti816x_evm_defconfig b/configs/ti816x_evm_defconfig > > index bf877f596b..131b25a188 100644 > > --- a/configs/ti816x_evm_defconfig > > +++ b/configs/ti816x_evm_defconfig > > @@ -46,6 +46,7 @@ CONFIG_MMC_OMAP_HS=y > > CONFIG_NAND=y > > CONFIG_SYS_NAND_BUSWIDTH_16BIT=y > > CONFIG_MII=y > > +CONFIG_DM_ETH=y > > CONFIG_DRIVER_TI_EMAC=y > > CONFIG_SYS_NS16550=y > > CONFIG_SPI=y > > diff --git a/drivers/net/ti/davinci_emac.c b/drivers/net/ti/davinci_emac.c > > index 9d53984973..3252a235d2 100644 > > --- a/drivers/net/ti/davinci_emac.c > > +++ b/drivers/net/ti/davinci_emac.c > > @@ -26,11 +26,13 @@ > > #include <net.h> > > #include <miiphy.h> > > #include <malloc.h> > > -#include <netdev.h> > > #include <linux/compiler.h> > > #include <asm/arch/emac_defs.h> > > #include <asm/io.h> > > #include "davinci_emac.h" > > +#ifndef CONFIG_DM_ETH > > +#include <netdev.h> > > +#endif > > > > unsigned int emac_dbg = 0; > > #define debug_emac(fmt,args...) if (emac_dbg) printf(fmt,##args) > > @@ -107,10 +109,16 @@ static u_int8_t num_phy; > > > > phy_t phy[CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT]; > > > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > static int davinci_eth_set_mac_addr(struct eth_device *dev) > > +#else /* with CONFIG_DM_ETH */ > > +static int davinci_emac_write_hwaddr(struct udevice *dev) > > +#endif /* CONFIG_DM_ETH */ > > { > > - unsigned long mac_hi; > > - unsigned long mac_lo; > > +#ifdef CONFIG_DM_ETH > > + struct eth_pdata *pdata = dev_get_platdata(dev); > > +#endif > > + unsigned long mac_hi, mac_lo; > > > > /* > > * Set MAC Addresses & Init multicast Hash to 0 (disable any > > multicast > > @@ -118,12 +126,22 @@ static int davinci_eth_set_mac_addr(struct eth_device > > *dev) > > * Using channel 0 only - other channels are disabled > > * */ > > writel(0, &adap_emac->MACINDEX); > > + > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > mac_hi = (dev->enetaddr[3] << 24) | > > (dev->enetaddr[2] << 16) | > > (dev->enetaddr[1] << 8) | > > (dev->enetaddr[0]); > > mac_lo = (dev->enetaddr[5] << 8) | > > (dev->enetaddr[4]); > > +#else /* with CONFIG_DM_ETH */ > > + mac_hi = (pdata->enetaddr[3] << 24) | > > + (pdata->enetaddr[2] << 16) | > > + (pdata->enetaddr[1] << 8) | > > + (pdata->enetaddr[0]); > > + mac_lo = (pdata->enetaddr[5] << 8) | > > + (pdata->enetaddr[4]); > > +#endif /* CONFIG_DM_ETH */ > > > > writel(mac_hi, &adap_emac->MACADDRHI); > > #if defined(DAVINCI_EMAC_VERSION2) > > @@ -411,13 +429,17 @@ static void __attribute__((unused)) > > davinci_eth_gigabit_enable(int phy_addr) > > } > > > > /* Eth device open */ > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > static int davinci_eth_open(struct eth_device *dev, bd_t *bis) > > +#else /* with CONFIG_DM_ETH */ > > +static int davinci_emac_start(struct udevice *dev) > > +#endif /* CONFIG_DM_ETH */ > > { > > - dv_reg_p addr; > > - u_int32_t clkdiv, cnt, mac_control; > > - uint16_t __maybe_unused lpa_val; > > - volatile emac_desc *rx_desc; > > - int index; > > + u32 clkdiv, cnt, mac_control; > > + volatile emac_desc *rx_desc; > > + u16 __maybe_unused lpa_val; > > + dv_reg_p addr; > > + int index; > > > > debug_emac("+ emac_open\n"); > > > > @@ -447,7 +469,11 @@ static int davinci_eth_open(struct eth_device *dev, > > bd_t *bis) > > writel(1, &adap_emac->TXCONTROL); > > writel(1, &adap_emac->RXCONTROL); > > > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > davinci_eth_set_mac_addr(dev); > > +#else /* with CONFIG_DM_ETH */ > > + davinci_emac_write_hwaddr(dev); > > +#endif /* CONFIG_DM_ETH */ > > > > /* Set DMA 8 TX / 8 RX Head pointers to 0 */ > > addr = &adap_emac->TX0HDP; > > @@ -588,7 +614,11 @@ static void davinci_eth_ch_teardown(int ch) > > } > > > > /* Eth device close */ > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > static void davinci_eth_close(struct eth_device *dev) > > +#else /* with CONFIG_DM_ETH */ > > +static void davinci_emac_stop(struct udevice *dev) > > +#endif /* CONFIG_DM_ETH */ > > { > > debug_emac("+ emac_close\n"); > > > > @@ -619,11 +649,15 @@ static int tx_send_loop = 0; > > * This function sends a single packet on the network and returns > > * positive number (number of bytes transmitted) or negative for error > > */ > > -static int davinci_eth_send_packet (struct eth_device *dev, > > - void *packet, int length) > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > +static int davinci_eth_send_packet(struct eth_device *dev, > > + void *packet, int length) > > +#else /* with CONFIG_DM_ETH */ > > +static int davinci_emac_send(struct udevice *dev, > > + void *packet, int length) > > +#endif /* CONFIG_DM_ETH */ > > { > > - int ret_status = -1; > > - int index; > > + int ret_status = -1, index; > > I'm not sure why you are mixing these formatting changes (which look > bad anyway) with the substantive changes. Please drop them. > > > tx_send_loop = 0; > > > > index = get_active_phy(); > > @@ -672,7 +706,11 @@ static int davinci_eth_send_packet (struct eth_device > > *dev, > > /* > > * This function handles receipt of a packet from the network > > */ > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > static int davinci_eth_rcv_packet (struct eth_device *dev) > > +#else /* with CONFIG_DM_ETH */ > > +static int davinci_emac_recv(struct udevice *dev, int flags, uchar > > **packetp) > > +#endif /* CONFIG_DM_ETH */ > > { > > volatile emac_desc *rx_curr_desc; > > volatile emac_desc *curr_desc; > > Please remove the call to net_process_received_packet() and split the > descriptor cleanup into a free_pkt() operation. > > > @@ -742,6 +780,9 @@ static int davinci_eth_rcv_packet (struct eth_device > > *dev) > > } > > return (ret); > > } > > +#ifdef CONFIG_DM_ETH > > + *packetp = rx_curr_desc->buffer; > > +#endif > > return (0); > > } > > > > @@ -750,12 +791,16 @@ static int davinci_eth_rcv_packet (struct eth_device > > *dev) > > * EMAC modules power or pin multiplexors, that is done by board_init() > > * much earlier in bootup process. Returns 1 on success, 0 otherwise. > > */ > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > int davinci_emac_initialize(void) > > +#else /* with CONFIG_DM_ETH */ > > +static int davinci_emac_probe(struct udevice *dev) > > +#endif /* CONFIG_DM_ETH */ > > { > > - u_int32_t phy_id; > > - u_int16_t tmp; > > - int i; > > - int ret; > > + int i, ret; > > + u32 phy_id; > > + u16 tmp; > > +#ifndef CONFIG_DM_ETH > > struct eth_device *dev; > > > > dev = malloc(sizeof *dev); > > @@ -774,6 +819,7 @@ int davinci_emac_initialize(void) > > dev->write_hwaddr = davinci_eth_set_mac_addr; > > > > eth_register(dev); > > +#endif /* CONFIG_DM_ETH */ > > > > davinci_eth_mdio_enable(); > > > > @@ -854,5 +900,34 @@ int davinci_emac_initialize(void) > > phy[i].auto_negotiate(i); > > } > > #endif > > - return(1); > > + > > +#ifndef CONFIG_DM_ETH > > When you have both cases, please use positive logic. Flip the cases > and use #ifdef. > > > + return 1; > > +#else /* with CONFIG_DM_ETH */ > > + return 0; > > +#endif /* CONFIG_DM_ETH */ > > } > > + > > +#ifdef CONFIG_DM_ETH > > +static const struct eth_ops davinci_emac_ops = { > > + .start = davinci_emac_start, > > + .send = davinci_emac_send, > > + .recv = davinci_emac_recv, > > + .stop = davinci_emac_stop, > > + .write_hwaddr = davinci_emac_write_hwaddr, > > +}; > > + > > +static const struct udevice_id davinci_emac_ids[] = { > > + { .compatible = "ti,davinci-dm6467-emac" }, > > + { } > > +}; > > + > > +U_BOOT_DRIVER(davinci_emac) = { > > + .name = "davinci_emac", > > + .id = UCLASS_ETH, > > + .of_match = davinci_emac_ids, > > + .probe = davinci_emac_probe, > > + .ops = &davinci_emac_ops, > > + .platdata_auto_alloc_size = sizeof(struct eth_pdata), > > +}; > > +#endif /* CONFIG_DM_ETH */ > > -- > > 2.21.0 > > > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > https://lists.denx.de/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
