On Thu, 2019-05-02 at 08:11 +0200, Anatolij Gustschin wrote:
> Hi Heiko,
>
> On Thu, 2 May 2019 07:39:06 +0200
> Heiko Schocher h...@denx.de wrote:
> ...
> >
> > @Anatolij: Is this code needed anymore, as board is moved to DM ?
>
> ...
> > dm_i2c_probe should initialize the i2c bus completly, also we need
> > not longer the:
> >
> > #ifdef CONFIG_DM_I2C
> >
> > and remove the else part ... or ? Can you test this change?
>
> The DM conversion is not complete yet and I still need the
> possibility to revert to non-DM code for various video tests
> to complete the DM_VIDEO/DM_I2C conversion, so that video
> related stuff works on i.MX boards similar as before the
> conversion. Unfortunately, I do not have time for this now,
> this must wait. Sorry.
>
> Anatolij
Would something like this be ok? It will allow removing the MXC
hardcoded speeds when using DM_I2C. It also makes it more clear in
wandboard.c that the speed is not used when using DM_I2C.
--- a/board/wandboard/wandboard.c
+++ b/board/wandboard/wandboard.c
@@ -46,6 +46,15 @@ DECLARE_GLOBAL_DATA_PTR;
#define ETH_PHY_AR8035_POWER IMX_GPIO_NR(7, 13)
#define REV_DETECTION IMX_GPIO_NR(2, 28)
+/* Speed defined in Kconfig is only applicable when not using DM_I2C. */
+#ifdef CONFIG_DM_I2C
+#define I2C1_SPEED_NON_DM 0
+#define I2C2_SPEED_NON_DM 0
+#else
+#define I2C1_SPEED_NON_DM CONFIG_SYS_MXC_I2C1_SPEED
+#define I2C2_SPEED_NON_DM CONFIG_SYS_MXC_I2C2_SPEED
+#endif
+
static bool with_pmic;
int dram_init(void)
@@ -463,13 +472,13 @@ int board_init(void)
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#if defined(CONFIG_VIDEO_IPUV3)
- setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f, &mx6dl_i2c2_pad_info);
+ setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info);
if (is_mx6dq() || is_mx6dqp()) {
- setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f,
&mx6q_i2c2_pad_info);
- setup_i2c(2, CONFIG_SYS_MXC_I2C2_SPEED, 0x7f,
&mx6q_i2c3_pad_info);
+ setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6q_i2c2_pad_info);
+ setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6q_i2c3_pad_info);
} else {
- setup_i2c(1, CONFIG_SYS_MXC_I2C1_SPEED, 0x7f,
&mx6dl_i2c2_pad_info);
- setup_i2c(2, CONFIG_SYS_MXC_I2C2_SPEED, 0x7f,
&mx6dl_i2c3_pad_info);
+ setup_i2c(1, I2C1_SPEED_NON_DM, 0x7f, &mx6dl_i2c2_pad_info);
+ setup_i2c(2, I2C2_SPEED_NON_DM, 0x7f, &mx6dl_i2c3_pad_info);
}
setup_display();
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
