Add default configuration to run u-boot as BL33 in the boot flow case of ATF(ARM Trusted Firmware) -> OPTEE -> U-boot.
Signed-off-by: Jun Nie <jun....@linaro.org> --- configs/pico-imx7d_bl33_defconfig | 63 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 configs/pico-imx7d_bl33_defconfig diff --git a/configs/pico-imx7d_bl33_defconfig b/configs/pico-imx7d_bl33_defconfig new file mode 100644 index 0000000..a896cb3 --- /dev/null +++ b/configs/pico-imx7d_bl33_defconfig @@ -0,0 +1,63 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX7=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SECURE_BOOT=y +CONFIG_TARGET_PICO_IMX7D=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL=y +CONFIG_ARMV7_BOOT_SEC_DEFAULT=y +CONFIG_IMX_CONSOLE_UART_ID=5 +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_FIT_VERBOSE=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" +CONFIG_DEFAULT_FDT_FILE="imx7d-pico-pi.dtb" +CONFIG_BOUNCE_BUFFER=y +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_HUSH_PARSER=y +# CONFIG_CMD_BOOTD is not set +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_SPL=y +CONFIG_CMD_SPL_WRITE_SIZE=0x20000 +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_DFU=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PXE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="imx7d-pico-pi" +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DFU_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_MII=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_ETHER=y +CONFIG_USB_ETH_CDC=y +CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" +CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_OPTEE_TZDRAM_SIZE=0x2000000 -- 2.7.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
