On 3/27/19 10:12 AM, Neil Armstrong wrote:
> On 26/03/2019 16:53, Marek Vasut wrote:
>> On 3/26/19 4:15 PM, Neil Armstrong wrote:
>>> Adds support for Amlogic G12A USB Control Glue HW.
>>>
>>> The Amlogic G12A SoC Family embeds 2 USB Controllers :
>>> - a DWC3 IP configured as Host for USB2 and USB3
>>> - a DWC2 IP configured as Peripheral USB2 Only
>>>
>>> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
>>> to an USB3+PCIE Combo PHY shared with the PCIE controller.
>>>
>>> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
>>> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
>>> setups the on-chip OTG mode selection for this PHY.
>>>
>>> This driver sets the OTG capable port as Host mode by default,
>>> the switch to Device mode is to be done in a separate patch.
>>>
>>> Signed-off-by: Neil Armstrong <narmstr...@baylibre.com>
>>> ---
>>
>> [...]
>>
>>> +static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv)
>>> +{
>>> + int i, ret;
>>> +
>>> + for (i = 0 ; i < PHY_COUNT ; ++i) {
>>> + ret = generic_phy_get_by_name(priv->dev, phy_names[i],
>>> + &priv->phys[i]);
>>> + if (ret == -ENOENT)
>>> + continue;
>>> +
>>> + if (ret)
>>> + return ret;
>>> +
>>> + if (i == USB3_HOST_PHY)
>>> + priv->usb3_ports++;
>>> + else
>>> + priv->usb2_ports++;
>>> + }
>>> +
>>> + printf("%s: usb2 ports: %d\n", __func__, priv->usb2_ports);
>>> + printf("%s: usb3 ports: %d\n", __func__, priv->usb3_ports);
>>
>> Are these prints needed ?
>
> Nop, forgot to switch them to debug
>
>>
>>> + return 0;
>>> +}
>>
>> [...]
>>> +static int dwc3_meson_g12a_probe(struct udevice *dev)
>>> +{
>>> + struct dwc3_meson_g12a *priv = dev_get_platdata(dev);
>>> + int ret, i;
>>> +
>>> + priv->dev = dev;
>>> +
>>> + ret = regmap_init_mem(dev_ofnode(dev), &priv->regmap);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = dwc3_meson_g12a_clk_init(priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = dwc3_meson_g12a_reset_init(priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + ret = dwc3_meson_g12a_get_phys(priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> +#if CONFIG_IS_ENABLED(DM_REGULATOR)
>>> + ret = device_get_supply_regulator(dev, "vbus-supply",
>>> + &priv->vbus_supply);
>>> + if (ret && ret != -ENOENT) {
>>> + pr_err("Failed to get PHY regulator\n");
>>> + return ret;
>>> + }
>>> +
>>> + if (priv->vbus_supply) {
>>> + ret = regulator_set_enable(priv->vbus_supply, true);
>>> + if (ret)
>>> + return ret;
>>> + }
>>> +#endif
>>> +
>>> + priv->otg_mode = usb_get_dr_mode(dev_of_offset(dev));
>>> +
>>> + ret = dwc3_meson_g12a_usb_init(priv);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + for (i = 0 ; i < PHY_COUNT ; ++i) {
>>> + if (!priv->phys[i].dev)
>>> + continue;
>>> +
>>> + ret = generic_phy_init(&priv->phys[i]);
>>> + if (ret)
>>> + goto err_phy_init;
>>> + }
>>
>> Isn't there some function to init all the PHYs already ?
>>
>
> I don't see any in u-boot master !
> Unlike dwc3, we need to get the phys with the names to check if
> the USB3 phy is enabled, so we can't get all possible phys.
I see, so thus far my only comment is about the missed debug prints.
Thanks!
--
Best regards,
Marek Vasut
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
