Add default configuration to run u-boot as BL33 in the boot flow case of ATF(ARM Trusted Firmware) -> OPTEE -> U-boot.
Signed-off-by: Jun Nie <jun....@linaro.org> --- board/technexion/pico-imx7d/imximage-512MB.cfg | 95 ++++++++++++++++++++++++++ configs/pico-pi-imx7d_bl33_defconfig | 61 +++++++++++++++++ 2 files changed, 156 insertions(+) create mode 100644 board/technexion/pico-imx7d/imximage-512MB.cfg create mode 100644 configs/pico-pi-imx7d_bl33_defconfig diff --git a/board/technexion/pico-imx7d/imximage-512MB.cfg b/board/technexion/pico-imx7d/imximage-512MB.cfg new file mode 100644 index 0000000..2b7bbbc --- /dev/null +++ b/board/technexion/pico-imx7d/imximage-512MB.cfg @@ -0,0 +1,95 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2019 Arm Ltd. + * + * The DCD file for Pico-pi with 512MB DRAM memory. + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image. + * + * The syntax is taken as close as possible with the kwbimage + */ + +#define __ASSEMBLY__ +#include <config.h> + +IMAGE_VERSION 2 +#ifdef CONFIG_SECURE_BOOT +CSF CONFIG_CSF_SIZE +#endif + +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ + +DATA 4 0x30340004 0x4F400005 + +DATA 4 0x30391000 0x00000002 +DATA 4 0x307a0000 0x01040001 +DATA 4 0x307a0064 0x00400046 +DATA 4 0x307a0490 0x00000001 +DATA 4 0x307a00d4 0x00690000 +DATA 4 0x307a00d0 0x00020083 +DATA 4 0x307a00dc 0x09300004 +DATA 4 0x307a00e0 0x04080000 +DATA 4 0x307a00e4 0x00100004 +DATA 4 0x307a00f4 0x0000033f +DATA 4 0x307a0100 0x09081109 +DATA 4 0x307a0104 0x0007020d +DATA 4 0x307a0108 0x03040407 +DATA 4 0x307a010c 0x00002006 +DATA 4 0x307a0110 0x04020205 +DATA 4 0x307a0114 0x03030202 +DATA 4 0x307a0120 0x00000803 + +DATA 4 0x307a0180 0x00800020 +DATA 4 0x307a0190 0x02098204 +DATA 4 0x307a0194 0x00030303 +DATA 4 0x307a01a0 0x80400003 +DATA 4 0x307a01a4 0x00100020 +DATA 4 0x307a01a8 0x80100004 + +DATA 4 0x307a0200 0x0000001f +DATA 4 0x307a0204 0x00080808 +DATA 4 0x307a0210 0x00000f0f +DATA 4 0x307a0214 0x07070707 +DATA 4 0x307a0218 0x0f0f0707 +DATA 4 0x307a0240 0x06000604 +DATA 4 0x307a0244 0x00000001 + +DATA 4 0x30391000 0x00000000 +DATA 4 0x30790000 0x17420f40 +DATA 4 0x30790004 0x10210100 +DATA 4 0x30790010 0x00060807 +DATA 4 0x307900b0 0x1010007e + +DATA 4 0x3079009c 0x00000d6e + +DATA 4 0x30790030 0x08080808 +DATA 4 0x30790020 0x08080808 +DATA 4 0x30790050 0x01000010 +DATA 4 0x30790050 0x00000010 +DATA 4 0x30790018 0x0000000f +DATA 4 0x307900c0 0x0e407304 +DATA 4 0x307900c0 0x0e447304 +DATA 4 0x307900c0 0x0e447306 +DATA 4 0x307900c0 0x0e447304 + +CHECK_BITS_SET 4 0x307900c4 0x1 + +DATA 4 0x307900c0 0x0e447304 + +DATA 4 0x30384130 0x00000000 +DATA 4 0x30340020 0x00000178 +DATA 4 0x30384130 0x00000002 + +CHECK_BITS_SET 4 0x307a0004 0x1 diff --git a/configs/pico-pi-imx7d_bl33_defconfig b/configs/pico-pi-imx7d_bl33_defconfig new file mode 100644 index 0000000..7d1ac18 --- /dev/null +++ b/configs/pico-pi-imx7d_bl33_defconfig @@ -0,0 +1,61 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX7=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SECURE_BOOT=y +CONFIG_TARGET_PICO_IMX7D=y +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL=y +CONFIG_ARMV7_BOOT_SEC_DEFAULT=y +CONFIG_FIT=y +CONFIG_FIT_SIGNATURE=y +CONFIG_FIT_VERBOSE=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/technexion/pico-imx7d/imximage-512MB.cfg" +CONFIG_DEFAULT_FDT_FILE="imx7d-pico-pi.dtb" +CONFIG_BOUNCE_BUFFER=y +CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_HUSH_PARSER=y +# CONFIG_CMD_BOOTD is not set +CONFIG_CMD_BOOTZ=y +CONFIG_CMD_SPL=y +CONFIG_CMD_SPL_WRITE_SIZE=0x20000 +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_DFU=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PXE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DFU_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_PHYLIB=y +CONFIG_MII=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_USB_ETHER=y +CONFIG_USB_ETH_CDC=y +CONFIG_USBNET_HOST_ADDR="de:ad:be:af:00:00" +CONFIG_OF_LIBFDT=y +CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_OPTEE_TZDRAM_SIZE=0x2000000 -- 2.7.4 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
