On 07/03/2019 03:37, Krzysztof Kozlowski wrote: > Hi, > > Changes since v4 > ================ > 1. Patch 3: Fix build of trats/trats2 and other by hiding new call > behind check for CONFIG_BOARD_TYPES. > > Changes since v3 > ================ > 1. Add accumulated review and test tags. > 2. Patch 6: Add "ramp" keyword to new function (as discussed with > Torsten Duwe). > 3. Rebased on v2019.04-rc3. > > > Changes since v2 > ================ > 1. Add Lukasz review tags. > 2. Patch 7: Return on error, as suggested by Simon. > 2. Patch 3: Use IS_ENABLED() to run revision detection only > once - either during late display board or misc_init_r. > > Changes since v1 > ================ > 1. Move fixes to beginning of patchset. > 2. Patch 3: Rework the idea - split revision detection to be executed later. > 3. Patch 4: New patch. > 4. Patch 6: Apply Simon's comments. > 5. Patch 6: Do not delay when changing voltage if regulator is disabled. > 6. Patch 6: Do not delay when disabling the regulator. > > > Description > =========== > Odroid HC1 does not reboot properly (at least from SD card but > I do not expect difference on eMMC), if LDO4/VDD_ADC was turned > off by Linux kernel. This condition happens so far always, because > Linux kernel did not enable ADC on Odroid HC1, therefore the > VDD_ADC regulator was turned off as unused. > > The issue is in detection of revision which later is used to load > proper DTB. > > The revision is obtained by ADC read of a voltage depending on VDD_ADC. > Therefore: > 1. VDD_ADC has to be turned on (but board detection happens before > power is initialized), > 2. Turning VDD_ADC should wait with ramp delay, > 3. Reading the value from ADC should wait for it to stabilize. > > Tested on Odroid XU3-Lite and Odroid HC1. > > Comments and testing are welcomed. > > Best regards, > Krzysztof > > > Krzysztof Kozlowski (9): > adc: exynos-adc: Fix wrong bit operation used to stop the ADC > power: regulator: s2mps11: Fix step for LDO27 and LDO35 > arm: exynos: Detect revision later, when all resources are ready > arm: exynos: odroid-xu3: Display info late to have proper type > arm: exynos: Wait till ADC stabilizes before checking Odroid HC1 > revision > regulator: Add support for ramp delay > power: regulator: s2mps11: Add enable delay > arm: dts: exynos: Add supply for ADC block to Odroid XU3 family > arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid > XU3 family > > arch/arm/dts/exynos5422-odroidxu3.dts | 20 +++++++ > board/samsung/common/board.c | 25 ++++++++- > board/samsung/common/exynos5-dt-types.c | 54 +++++++++++++++++-- > board/samsung/odroid/odroid.c | 8 +++ > configs/odroid-xu3_defconfig | 2 + > .../regulator/regulator.txt | 2 + > drivers/adc/exynos-adc.c | 2 +- > drivers/power/regulator/regulator-uclass.c | 47 +++++++++++++++- > drivers/power/regulator/s2mps11_regulator.c | 15 +++++- > include/power/regulator.h | 2 + > include/samsung/misc.h | 1 + > 11 files changed, 168 insertions(+), 10 deletions(-) >
applied to u-boot-samsung. Thanks, Minkyu Kang. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot