Convert the board to support the USB and video driver model and remove
the unnecessary code.
---
board/ronetix/pm9263/pm9263.c | 93 -----------------------------------
configs/pm9263_defconfig | 3 ++
2 files changed, 3 insertions(+), 93 deletions(-)
diff --git a/board/ronetix/pm9263/pm9263.c b/board/ronetix/pm9263/pm9263.c
index 692288d52e..2da39c4acd 100644
--- a/board/ronetix/pm9263/pm9263.c
+++ b/board/ronetix/pm9263/pm9263.c
@@ -17,8 +17,6 @@
#include <asm/arch/at91_matrix.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <lcd.h>
-#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
@@ -109,32 +107,6 @@ static void pm9263_macb_hw_init(void)
#endif
#ifdef CONFIG_LCD
-vidinfo_t panel_info = {
- .vl_col = 240,
- .vl_row = 320,
- .vl_clk = 4965000,
- .vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
- ATMEL_LCDC_INVFRAME_INVERTED,
- .vl_bpix = 3,
- .vl_tft = 1,
- .vl_hsync_len = 5,
- .vl_left_margin = 1,
- .vl_right_margin = 33,
- .vl_vsync_len = 1,
- .vl_upper_margin = 1,
- .vl_lower_margin = 0,
- .mmio = ATMEL_BASE_LCDC,
-};
-
-void lcd_enable(void)
-{
- at91_set_pio_value(AT91_PIO_PORTA, 22, 1); /* power up */
-}
-
-void lcd_disable(void)
-{
- at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */
-}
#ifdef CONFIG_LCD_IN_PSRAM
@@ -226,32 +198,6 @@ static int pm9263_lcd_hw_psram_init(void)
static void pm9263_lcd_hw_init(void)
{
- at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */
- at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
- at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */
- at91_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDDEN */
- at91_set_b_periph(AT91_PIO_PORTB, 9, 0); /* LCDCC */
- at91_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD2 */
- at91_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD3 */
- at91_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD4 */
- at91_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD5 */
- at91_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD6 */
- at91_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD7 */
- at91_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD10 */
- at91_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD11 */
- at91_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD12 */
- at91_set_b_periph(AT91_PIO_PORTC, 12, 0); /* LCDD13 */
- at91_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD14 */
- at91_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD15 */
- at91_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD18 */
- at91_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD19 */
- at91_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDD20 */
- at91_set_b_periph(AT91_PIO_PORTC, 17, 0); /* LCDD21 */
- at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */
- at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
-
- at91_periph_clk_enable(ATMEL_ID_LCDC);
-
/* Power Control */
at91_set_pio_output(AT91_PIO_PORTA, 22, 1);
at91_set_pio_value(AT91_PIO_PORTA, 22, 0); /* power down */
@@ -267,45 +213,6 @@ static void pm9263_lcd_hw_init(void)
}
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
-
-extern flash_info_t flash_info[];
-
-void lcd_show_board_info(void)
-{
- ulong dram_size, nand_size, flash_size;
- int i;
- char temp[32];
-
- lcd_printf ("%s\n", U_BOOT_VERSION);
- lcd_printf ("(C) 2009 Ronetix GmbH\n");
- lcd_printf ("supp...@ronetix.at\n");
- lcd_printf ("%s CPU at %s MHz",
- CONFIG_SYS_AT91_CPU_NAME,
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
-
- nand_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += get_nand_dev_by_index(i)->size;
-
- flash_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++)
- flash_size += flash_info[i].size;
-
- lcd_printf ("%ld MB SDRAM, %ld MB NAND\n%ld MB NOR Flash\n"
- "4 MB PSRAM\n",
- dram_size >> 20,
- nand_size >> 20,
- flash_size >> 20);
-}
-#endif /* CONFIG_LCD_INFO */
-
#endif /* CONFIG_LCD */
int board_early_init_f(void)
diff --git a/configs/pm9263_defconfig b/configs/pm9263_defconfig
index ceb7efe503..29352f3377 100644
--- a/configs/pm9263_defconfig
+++ b/configs/pm9263_defconfig
@@ -30,6 +30,7 @@ CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9263ek"
CONFIG_ENV_IS_IN_FLASH=y
CONFIG_DM=y
+CONFIG_BLK=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_DM_GPIO=y
@@ -49,5 +50,7 @@ CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_STORAGE=y
CONFIG_LCD=y
+CONFIG_DM_VIDEO=y
--
2.17.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
