On Wed, 6 Mar 2019 at 08:03, Minkyu Kang <mk7.k...@samsung.com> wrote: > > Dear Krzysztof Kozlowski, > > On 06/03/2019 04:57, Krzysztof Kozlowski wrote: > > Hi, > > > > Changes since v3 > > ================ > > 1. Add accumulated review and test tags. > > 2. Patch 6: Add "ramp" keyword to new function (as discussed with > > Torsten Duwe). > > 3. Rebased on v2019.04-rc3. > > > > > > Changes since v2 > > ================ > > 1. Add Lukasz review tags. > > 2. Patch 7: Return on error, as suggested by Simon. > > 2. Patch 3: Use IS_ENABLED() to run revision detection only > > once - either during late display board or misc_init_r. > > > > Changes since v1 > > ================ > > 1. Move fixes to beginning of patchset. > > 2. Patch 3: Rework the idea - split revision detection to be executed later. > > 3. Patch 4: New patch. > > 4. Patch 6: Apply Simon's comments. > > 5. Patch 6: Do not delay when changing voltage if regulator is disabled. > > 6. Patch 6: Do not delay when disabling the regulator. > > > > > > Description > > =========== > > Odroid HC1 does not reboot properly (at least from SD card but > > I do not expect difference on eMMC), if LDO4/VDD_ADC was turned > > off by Linux kernel. This condition happens so far always, because > > Linux kernel did not enable ADC on Odroid HC1, therefore the > > VDD_ADC regulator was turned off as unused. > > > > The issue is in detection of revision which later is used to load > > proper DTB. > > > > The revision is obtained by ADC read of a voltage depending on VDD_ADC. > > Therefore: > > 1. VDD_ADC has to be turned on (but board detection happens before > > power is initialized), > > 2. Turning VDD_ADC should wait with ramp delay, > > 3. Reading the value from ADC should wait for it to stabilize. > > > > Tested on Odroid XU3-Lite and Odroid HC1. > > > > Comments and testing are welcomed. > > > > Best regards, > > Krzysztof > > > > Krzysztof Kozlowski (9): > > adc: exynos-adc: Fix wrong bit operation used to stop the ADC > > power: regulator: s2mps11: Fix step for LDO27 and LDO35 > > arm: exynos: Detect revision later, when all resources are ready > > arm: exynos: odroid-xu3: Display info late to have proper type > > arm: exynos: Wait till ADC stabilizes before checking Odroid HC1 > > revision > > regulator: Add support for ramp delay > > power: regulator: s2mps11: Add enable delay > > arm: dts: exynos: Add supply for ADC block to Odroid XU3 family > > arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid > > XU3 family > > > > arch/arm/dts/exynos5422-odroidxu3.dts | 20 +++++++ > > board/samsung/common/board.c | 24 ++++++++- > > board/samsung/common/exynos5-dt-types.c | 54 +++++++++++++++++-- > > board/samsung/odroid/odroid.c | 8 +++ > > configs/odroid-xu3_defconfig | 2 + > > .../regulator/regulator.txt | 2 + > > drivers/adc/exynos-adc.c | 2 +- > > drivers/power/regulator/regulator-uclass.c | 47 +++++++++++++++- > > drivers/power/regulator/s2mps11_regulator.c | 15 +++++- > > include/power/regulator.h | 2 + > > include/samsung/misc.h | 1 + > > 11 files changed, 167 insertions(+), 10 deletions(-) > > > > Build was failed after apply your patch on trats, trats2 and > s5pc210_universal. > Please check. > > board/samsung/common/built-in.o: In function `misc_init_r': > /home/share/Work/u-boot-samsung/board/samsung/common/board.c:307: undefined > reference to `set_board_revision'
Indeed, I need to update other boards as well. I'll fix it. Best regards, Krzysztof _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot