On Tue, Feb 12, 2019 at 1:20 PM Adam Ford <aford...@gmail.com> wrote:
>
> On Sun, Feb 10, 2019 at 10:37 PM Vignesh R <vigne...@ti.com> wrote:
> >
> >
> >
> > On 11/02/19 9:01 AM, Adam Ford wrote:
> > > On Tue, Feb 5, 2019 at 12:00 AM Vignesh R <vigne...@ti.com> wrote:
> > >>
> > >> Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD
> > >> layer. Fix up sf_dataflash to work in legacy way. And update sandbox to
> > >> use new interfaces/definitions
> > >>
> > >> Signed-off-by: Vignesh R <vigne...@ti.com>
> > >> Tested-by: Simon Goldschmidt <simon.k.r.goldschm...@gmail.com>
> > >> Tested-by: Stefan Roese <s...@denx.de>
> > >> Tested-by: Horatiu Vultur <horatiu.vul...@microchip.com>
> > >> Reviewed-by: Jagan Teki <ja...@openedev.com>
> > >> Tested-by: Jagan Teki <ja...@amarulasolutions.com> #zynq-microzed
> > >
> > > This patch appears to break the da850_evm board which boots from SPI
> > > Flash and initializes the davinci driver with platdata since the
> > > device tree stuff does not quite work right in SPL.
> >
> > Oops, I did test on K2G EVM that has davinci SPI controller with micron
> > n25q flash but that was with DT. Not sure whats missing with platdata.
> >
> > >
> > > U-Boot SPL 2019.01-02923-gc4e8862308-dirty (Feb 10 2019 - 21:24:38 -0600)
> > > Trying to boot from SPI
> > > SPI probe failed.
> > > SPL: failed to boot from all boot devices
> > > ### ERROR ### Please RESET the board ###
> >
> > Could you enable debug prints at spi-mem level in drivers/spi/spi-mem.c
> > (especially debug prints at the end of spi_mem_exec_op()) and post the
> > logs here?
> >
> > >
> > > Any suggestions on how to fix the SPI initialization without needing
> > > the device tree? I have tried to port the device tree stuff to SPL,
> > > but I haven't yet been successful so I have had to leave the platdata
> > > initialization in place.
> > >
> >
> > I haven't changed any driver names so, platdata to driver bindings
> > should still be the same. Could you verify if spi_nor_scan() is being
> > called in drivers/mtd/spi/spi-nor-tiny.c for SPL?
>
> I globally turned on DEBUG and I have two logs for you:
>
> Not working:
>
> U-Boot SPL 2019.01-02923-gc4e8862308-dirty (Feb 12 2019 - 13:04:19 -0600)
> Trying to boot from SPI
> uclass_find_device_by_seq: 0 -1
> uclass_find_device_by_seq: 0 0
> - -1 -1 'davinci_spi'
> - not found
> spi_get_bus_and_cs: Binding new device 'spi_flash', busnum=0, cs=0,
> driver=spi_flash_std
> spi_get_bus_and_cs: Error path, created=1, device 'spi_flash'
> SPI probe failed.
> SPL: failed to boot from all boot devices
> ### ERROR ### Please RESET the board ###
>
> As a point of reference , I thought I'd show
> WORKING version (before this patch):
>
> U-Boot SPL 2019.01-02922-g2ee6705be0-dirty (Feb 12 2019 - 12:59:49 -0600)
> Trying to boot from SPI
> uclass_find_device_by_seq: 0 -1
> uclass_find_device_by_seq: 0 0
> - -1 -1 'davinci_spi'
> - not found
> spi_get_bus_and_cs: Binding new device 'spi_flash', busnum=0, cs=0,
> driver=spi_flash_std
> uclass_find_device_by_seq: 0 -1
> uclass_find_device_by_seq: 0 0
> - -1 -1 'spi_flash'
> - not found
> spi_flash_std_probe: slave=8001fd60, cs=0
> davinci_spi_set_speed speed 30000000
> davinci_spi_set_mode mode 3
> davinci_spi_set_speed speed 30000000
> davinci_spi_set_mode mode 3
> spi_get_bus_and_cs: bus=8001fbf4, slave=8001fd60
> SPL: payload image: U-Boot 2019.01-02922-g2ee6705be0 load addr:
> 0xc107ffc0 size: 405306
> Jumping to U-Boot
> loaded - jumping to U-Boot...
> image entry point: 0xc1080000
> ...
>
> During this process, I learned a few things.
> 1. I am not really using the device tree during SPL like i originally
> thought and the OF_PLATDATA
> 2. Getting SPL to support device tree with or without PLATDATA isn't
> as straightforward as I hoped
> 3. With the knowledge I learned from item 1, I tried to disabled
> OF_CONTROL during SPL, but this patch also fails to build since it
> assumes OF_CONTROL is always enabled.
>
> If there are any suggestions you might have, I am willing to try them.
>
I beleive I have narrowed it down a bit to a chunk of code (int
device_probe(struct udevice *dev)) located in device.c:
/* Allocate private data if requested and not reentered */
if (drv->priv_auto_alloc_size && !dev->priv) {
dev->priv = alloc_priv(drv->priv_auto_alloc_size, drv->flags);
if (!dev->priv) {
printf("Allocate private data if requested and not reentered\n");
ret = -ENOMEM;
goto fail;
}
}
I am not sure how the sizes are defined and/or allocated
adam
> adam
>
> >
> > Sorry for the trouble.
> >
> > Regards
> > Vignesh
> >
> >
> > --
> > Regards
> > Vignesh
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
