[U-Boot] [RESEND PATCH] drivers: esdhc: add support for ColdFire mcf5441x family

[Angelo Dureghello]

This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.

Signed-off-by: Angelo Dureghello <ang...@sysam.it>
---
Changes in v2:
- add be to le 32-bit byte swap for ColdFire,
- remove HS from host capabilities for ColdFire.
---
 drivers/mmc/fsl_esdhc.c | 43 ++++++++++++++++++++++++++++++++++++++++-
 include/fsl_esdhc.h     |  1 +
 2 files changed, 43 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 99e5882866..c972412574 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -384,6 +384,25 @@ static void check_and_invalidate_dcache_range
        invalidate_dcache_range(start, end);
 }
 
+#ifdef CONFIG_MCF5441x
+/*
+ * Swaps 32-bit words to little-endian byte order.
+ */
+static inline void sd_swap_dma_buff(struct mmc_data *data)
+{
+       int i, size = data->blocksize >> 2;
+       u32 *buffer = (u32 *)data->dest;
+       u32 sw;
+
+       while (data->blocks--) {
+               for (i = 0; i < size; i++) {
+                       sw = __sw32(*buffer);
+                       *buffer++ = sw;
+               }
+       }
+}
+#endif
+
 /*
  * Sends a command out on the bus.  Takes the mmc pointer,
  * a command pointer, and an optional data pointer.
@@ -546,8 +565,12 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv 
*priv, struct mmc *mmc,
                 * cache-fill during the DMA operations such as the
                 * speculative pre-fetching etc.
                 */
-               if (data->flags & MMC_DATA_READ)
+               if (data->flags & MMC_DATA_READ) {
                        check_and_invalidate_dcache_range(cmd, data);
+#ifdef CONFIG_MCF5441x
+                       sd_swap_dma_buff(data);
+#endif
+               }
 #endif
        }
 
@@ -1029,8 +1052,12 @@ static int esdhc_init_common(struct fsl_esdhc_priv 
*priv, struct mmc *mmc)
        /* Disable the BRR and BWR bits in IRQSTAT */
        esdhc_clrbits32(&regs->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
 
+#ifdef CONFIG_MCF5441x
+       esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
+#else
        /* Put the PROCTL reg back to the default */
        esdhc_write32(&regs->proctl, PROCTL_INIT);
+#endif
 
        /* Set timout to the maximum value */
        esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
@@ -1138,6 +1165,11 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
        if (ret)
                return ret;
 
+#ifdef CONFIG_MCF5441x
+       /* ColdFire, using SDHC_DATA[3] for card detection */
+       esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
+#endif
+
 #ifndef CONFIG_FSL_USDHC
        esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
                                | SYSCTL_IPGEN | SYSCTL_CKEN);
@@ -1162,6 +1194,15 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
        voltage_caps = 0;
        caps = esdhc_read32(&regs->hostcapblt);
 
+#ifdef CONFIG_MCF5441x
+       /*
+        * MCF5441x RM declares in more points that sdhc clock speed must
+        * never exceed 25 Mhz. From this, the HS bit needs to be disabled
+        * from host capabilities.
+        */
+       caps &= ~ESDHC_HOSTCAPBLT_HSS;
+#endif
+
 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
        caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
                        ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30);
diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h
index acd8dd06f8..8dbd5249a7 100644
--- a/include/fsl_esdhc.h
+++ b/include/fsl_esdhc.h
@@ -106,6 +106,7 @@
 #define PROCTL_INIT            0x00000020
 #define PROCTL_DTW_4           0x00000002
 #define PROCTL_DTW_8           0x00000004
+#define PROCTL_D3CD            0x00000008
 
 #define CMDARG                 0x0002e008
 
-- 
2.20.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot