Am Do., 27. Dez. 2018 um 12:51 Uhr schrieb Lars Povlsen
<lars.povl...@microchip.com>:
>
> This add support for the the MSCC serial GPIO driver in MSCC
> VCoreIII-based SOCs.
>
> By using a serial interface, the SIO controller significantly extends
> the number of available GPIOs with a minimum number of additional pins
> on the device. The primary purpose of the SIO controller is to connect
> control signals from SFP modules and to act as an LED controller.
>
> This adds the base driver.
>
> Signed-off-by: Lars Povlsen <lars.povl...@microchip.com>
> ---
> MAINTAINERS | 1 +
> drivers/gpio/Kconfig | 11 ++
> drivers/gpio/Makefile | 1 +
> drivers/gpio/mscc_sgpio.c | 274 ++++++++++++++++++++++++++++++++++++++
> 4 files changed, 287 insertions(+)
> create mode 100644 drivers/gpio/mscc_sgpio.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index ae825014bd..494962e9b3 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -523,6 +523,7 @@ F: arch/mips/dts/mscc*
> F: arch/mips/dts/ocelot*
> F: board/mscc/
> F: configs/mscc*
> +F: drivers/gpio/mscc_sgpio.c
> F: include/configs/vcoreiii.h
>
> MIPS JZ4780
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index c8c6c60623..aa55ff43c4 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -106,6 +106,17 @@ config MSCC_BITBANG_SPI_GPIO
> Support controlling the GPIO used for SPI bitbang by software. Can
> be used by the VCoreIII SoCs, but it was mainly useful for Luton.
>
> +config MSCC_SGPIO
> + bool "Microsemi Serial GPIO driver"
> + depends on DM_GPIO && SOC_VCOREIII
> + help
> + Support for the VCoreIII SoC serial GPIO device. By using a
> + serial interface, the SIO controller significantly extends
> + the number of available GPIOs with a minimum number of
> + additional pins on the device. The primary purpose of the
> + SIO controller is to connect control signals from SFP
> + modules and to act as an LED controller.
> +
> config MSM_GPIO
> bool "Qualcomm GPIO driver"
> depends on DM_GPIO
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index 61feda1537..be2b3c792f 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -60,3 +60,4 @@ obj-$(CONFIG_$(SPL_)PCF8575_GPIO) += pcf8575_gpio.o
> obj-$(CONFIG_PM8916_GPIO) += pm8916_gpio.o
> obj-$(CONFIG_MT7621_GPIO) += mt7621_gpio.o
> obj-$(CONFIG_MSCC_BITBANG_SPI_GPIO) += gpio-mscc-bitbang-spi.o
> +obj-$(CONFIG_MSCC_SGPIO) += mscc_sgpio.o
> diff --git a/drivers/gpio/mscc_sgpio.c b/drivers/gpio/mscc_sgpio.c
> new file mode 100644
> index 0000000000..134d36066c
> --- /dev/null
> +++ b/drivers/gpio/mscc_sgpio.c
> @@ -0,0 +1,274 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Microsemi SoCs serial gpio driver
> + *
> + * Author: <lars.povl...@microchip.com>
> + *
> + * Copyright (c) 2018 Microsemi Corporation
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <errno.h>
> +#include <clk.h>
> +
> +#define MSCC_SGPIOS_PER_BANK 32
> +#define MSCC_SGPIO_BANK_DEPTH 4
> +
> +enum {
> + REG_INPUT_DATA,
> + REG_PORT_CONFIG,
> + REG_PORT_ENABLE,
> + REG_SIO_CONFIG,
> + REG_SIO_CLOCK,
> + MAXREG
> +};
> +
> +struct mscc_sgpio_bf {
> + u8 beg;
> + u8 end;
> +};
> +
> +struct mscc_sgpio_props {
> + u8 regoff[MAXREG];
> + struct mscc_sgpio_bf auto_repeat;
> + struct mscc_sgpio_bf port_width;
> + struct mscc_sgpio_bf clk_freq;
> + struct mscc_sgpio_bf bit_source;
> +};
> +
> +#define __M(bf) GENMASK((bf).end, (bf).beg)
> +#define __F(bf, x) (__M(bf) & ((x) << (bf).beg))
> +#define __X(bf, x) (((x) >> (bf).beg) & GENMASK(((bf).end - (bf).beg),
> 0))
> +
> +#define MSCC_M_CFG_SIO_AUTO_REPEAT(p) BIT(p->props->auto_repeat.beg)
> +#define MSCC_F_CFG_SIO_PORT_WIDTH(p, x)
> __F(p->props->port_width, x)
> +#define MSCC_M_CFG_SIO_PORT_WIDTH(p) __M(p->props->port_width)
> +#define MSCC_F_CLOCK_SIO_CLK_FREQ(p, x)
> __F(p->props->clk_freq, x)
> +#define MSCC_M_CLOCK_SIO_CLK_FREQ(p) __M(p->props->clk_freq)
> +#define MSCC_F_PORT_CFG_BIT_SOURCE(p, x) __F(p->props->bit_source, x)
> +#define MSCC_X_PORT_CFG_BIT_SOURCE(p, x) __X(p->props->bit_source, x)
> +
> +const struct mscc_sgpio_props props_luton = {
> + .regoff = { 0x00, 0x09, 0x29, 0x2a, 0x2b },
> + .auto_repeat = { 5, 5 },
> + .port_width = { 2, 3 },
> + .clk_freq = { 0, 11 },
> + .bit_source = { 0, 11 },
> +};
> +
> +const struct mscc_sgpio_props props_ocelot = {
> + .regoff = { 0x00, 0x06, 0x26, 0x04, 0x05 },
> + .auto_repeat = { 10, 10 },
> + .port_width = { 7, 8 },
> + .clk_freq = { 8, 19 },
> + .bit_source = { 12, 23 },
> +};
> +
> +struct mscc_sgpio_priv {
> + u32 bitcount;
> + u32 ports;
> + u32 clock;
> + u32 mode[MSCC_SGPIOS_PER_BANK];
> + u32 __iomem *regs;
> + const struct mscc_sgpio_props *props;
> +};
> +
> +static inline u32 sgpio_readl(struct mscc_sgpio_priv *priv, u32 rno, u32 off)
> +{
> + u32 __iomem *reg = &priv->regs[priv->props->regoff[rno] + off];
> +
> + return readl(reg);
> +}
> +
> +static inline void sgpio_writel(struct mscc_sgpio_priv *priv,
> + u32 val, u32 rno, u32 off)
> +{
> + u32 __iomem *reg = &priv->regs[priv->props->regoff[rno] + off];
> +
> + writel(val, reg);
> +}
> +
> +static void sgpio_clrsetbits(struct mscc_sgpio_priv *priv,
> + u32 rno, u32 off, u32 clear, u32 set)
> +{
> + u32 __iomem *reg = &priv->regs[priv->props->regoff[rno] + off];
> +
> + clrsetbits_le32(reg, clear, set);
> +}
> +
> +static int mscc_sgpio_direction_input(struct udevice *dev, unsigned int gpio)
> +{
> + struct mscc_sgpio_priv *priv = dev_get_priv(dev);
> +
> + u32 port = gpio % MSCC_SGPIOS_PER_BANK;
> + u32 bit = gpio / MSCC_SGPIOS_PER_BANK;
> +
> + priv->mode[port] |= BIT(bit);
> +
> + return 0;
> +}
> +
> +static int mscc_sgpio_direction_output(struct udevice *dev,
> + unsigned int gpio, int value)
> +{
> + struct mscc_sgpio_priv *priv = dev_get_priv(dev);
> + u32 port = gpio % MSCC_SGPIOS_PER_BANK;
> + u32 bit = gpio / MSCC_SGPIOS_PER_BANK;
> + u32 mask = 3 << (3 * bit);
> +
> + debug("set: port %d, bit %d, mask 0x%08x, value %d\n",
> + port, bit, mask, value);
> +
> + value = (value & 3) << (3 * bit);
> + sgpio_clrsetbits(priv, REG_PORT_CONFIG, port,
> + MSCC_F_PORT_CFG_BIT_SOURCE(priv, mask),
> + MSCC_F_PORT_CFG_BIT_SOURCE(priv, value));
> + clrbits_le32(&priv->mode[port], BIT(bit));
> +
> + return 0;
> +}
> +
> +static int mscc_sgpio_get_function(struct udevice *dev, unsigned int gpio)
> +{
> + struct mscc_sgpio_priv *priv = dev_get_priv(dev);
> + u32 port = gpio % MSCC_SGPIOS_PER_BANK;
> + u32 bit = gpio / MSCC_SGPIOS_PER_BANK;
> + u32 val = priv->mode[port] & BIT(bit);
> +
> + if (val)
> + return GPIOF_INPUT;
> + else
> + return GPIOF_OUTPUT;
> +}
> +
> +static int mscc_sgpio_set_value(struct udevice *dev,
> + unsigned int gpio, int value)
> +{
> + return mscc_sgpio_direction_output(dev, gpio, value);
> +}
> +
> +static int mscc_sgpio_get_value(struct udevice *dev, unsigned int gpio)
> +{
> + struct mscc_sgpio_priv *priv = dev_get_priv(dev);
> + u32 port = gpio % MSCC_SGPIOS_PER_BANK;
> + u32 bit = gpio / MSCC_SGPIOS_PER_BANK;
> + int ret;
> +
> + if (mscc_sgpio_get_function(dev, gpio) == GPIOF_INPUT) {
> + ret = !!(sgpio_readl(priv, REG_INPUT_DATA, bit) & BIT(port));
> + } else {
> + u32 portval = sgpio_readl(priv, REG_PORT_CONFIG, port);
> +
> + ret = MSCC_X_PORT_CFG_BIT_SOURCE(priv, portval);
> + ret = !!(ret & (3 << (3 * bit)));
> + }
> +
> + debug("get: gpio %d, port %d, bit %d, value %d\n",
> + gpio, port, bit, ret);
> + return ret;
> +}
> +
> +static int mscc_sgpio_get_count(struct udevice *dev)
> +{
> + struct ofnode_phandle_args args;
> + int count = 0, i = 0, ret;
> +
> + ret = dev_read_phandle_with_args(dev, "gpio-ranges", NULL, 3, i,
> &args);
> + while (ret != -ENOENT) {
> + count += args.args[2];
> + ret = dev_read_phandle_with_args(dev, "gpio-ranges", NULL, 3,
> + ++i, &args);
> + }
> + return count;
> +}
> +
> +static int mscc_sgpio_probe(struct udevice *dev)
> +{
> + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
> + struct mscc_sgpio_priv *priv = dev_get_priv(dev);
> + int err, div_clock = 0, port;
> + u32 val;
> + struct clk clk;
> +
> + err = clk_get_by_index(dev, 0, &clk);
> + if (!err) {
> + err = clk_get_rate(&clk);
> + if (!IS_ERR_VALUE(err))
> + div_clock = err;
shouldn't the probe fail without a clock?
> + } else {
> + debug("mscc_sgpio: failed to get clock\n");
> + return err;
> + }
> +
> + priv->props = (const struct mscc_sgpio_props
> *)dev_get_driver_data(dev);
> + priv->ports = dev_read_u32_default(dev, "mscc,sgpio-ports",
> 0xFFFFFFFF);
> + priv->clock = dev_read_u32_default(dev, "mscc,sgpio-frequency",
> + 12500000);
> + if (priv->clock <= 0 || priv->clock > div_clock) {
> + printf("mscc_sgpio: Invalid frequency %d\n", priv->clock);
> + return -EINVAL;
> + }
> +
> + uc_priv->gpio_count = mscc_sgpio_get_count(dev);
> + uc_priv->gpio_count = dev_read_u32_default(dev, "ngpios",
> + uc_priv->gpio_count);
> + if (uc_priv->gpio_count < 1 || uc_priv->gpio_count >
> + (4 * MSCC_SGPIOS_PER_BANK)) {
> + printf("mscc_sgpio: gpio count %d\n", uc_priv->gpio_count);
> + return -EINVAL;
> + }
> + priv->bitcount = DIV_ROUND_UP(uc_priv->gpio_count,
> + MSCC_SGPIOS_PER_BANK);
> + debug("probe: gpios = %d, bit-count = %d\n",
> + uc_priv->gpio_count, priv->bitcount);
> +
> + priv->regs = (u32 __iomem *)map_physmem(devfdt_get_addr(dev),
> + 0x100,
> + MAP_NOCACHE);
there is a wrapper dev_remap_addr() for this
> + uc_priv->bank_name = "sgpio";
> +
> + sgpio_clrsetbits(priv, REG_SIO_CONFIG, 0,
> + MSCC_M_CFG_SIO_PORT_WIDTH(priv),
> + MSCC_F_CFG_SIO_PORT_WIDTH(priv, priv->bitcount - 1) |
> + MSCC_M_CFG_SIO_AUTO_REPEAT(priv));
> + val = div_clock / priv->clock;
> + debug("probe: div-clock = %d KHz, freq = %d KHz, div = %d\n",
> + div_clock / 1000, priv->clock / 1000, val);
> + sgpio_clrsetbits(priv, REG_SIO_CLOCK, 0,
> + MSCC_M_CLOCK_SIO_CLK_FREQ(priv),
> + MSCC_F_CLOCK_SIO_CLK_FREQ(priv, val));
> +
> + for (port = 0; port < 32; port++)
> + sgpio_writel(priv, 0, REG_PORT_CONFIG, port);
> + sgpio_writel(priv, priv->ports, REG_PORT_ENABLE, 0);
> +
> + debug("probe: sgpio regs = %p\n", priv->regs);
> +
> + return 0;
> +}
> +
> +static const struct dm_gpio_ops mscc_sgpio_ops = {
> + .direction_input = mscc_sgpio_direction_input,
> + .direction_output = mscc_sgpio_direction_output,
> + .get_function = mscc_sgpio_get_function,
> + .get_value = mscc_sgpio_get_value,
> + .set_value = mscc_sgpio_set_value,
> +};
> +
> +static const struct udevice_id mscc_sgpio_ids[] = {
> + { .compatible = "mscc,luton-sgpio", .data = (ulong)&props_luton },
> + { .compatible = "mscc,ocelot-sgpio", .data = (ulong)&props_ocelot },
> + { }
> +};
> +
> +U_BOOT_DRIVER(gpio_mscc_sgpio) = {
> + .name = "mscc-sgpio",
> + .id = UCLASS_GPIO,
> + .of_match = mscc_sgpio_ids,
> + .ops = &mscc_sgpio_ops,
> + .probe = mscc_sgpio_probe,
> + .priv_auto_alloc_size = sizeof(struct mscc_sgpio_priv),
> +};
> --
> 2.19.2
>
--
- Daniel
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
