Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT
Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2
U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
CPU: NXP i.MX8QM RevB A53 at 142933 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW 9330215b
Boot: SD1
DRAM: 6 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial@5a060000
Out: serial@5a060000
Err: serial@5a060000
Net:
Error: ethernet@5b040000 address not set.
eth-1: ethernet@5b040000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng....@nxp.com>
---
arch/arm/dts/Makefile | 4 +-
arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi | 112 +++++++++++++++++++
arch/arm/dts/fsl-imx8qm-mek.dts | 184 ++++++++++++++++++++++++++++++++
arch/arm/mach-imx/imx8/Kconfig | 6 ++
board/freescale/imx8qm_mek/Kconfig | 14 +++
board/freescale/imx8qm_mek/MAINTAINERS | 6 ++
board/freescale/imx8qm_mek/Makefile | 8 ++
board/freescale/imx8qm_mek/README | 57 ++++++++++
board/freescale/imx8qm_mek/imx8qm_mek.c | 157 +++++++++++++++++++++++++++
board/freescale/imx8qm_mek/imximage.cfg | 19 ++++
board/freescale/imx8qm_mek/spl.c | 75 +++++++++++++
configs/imx8qm_mek_defconfig | 75 +++++++++++++
include/configs/imx8qm_mek.h | 176 ++++++++++++++++++++++++++++++
13 files changed, 892 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
create mode 100644 arch/arm/dts/fsl-imx8qm-mek.dts
create mode 100644 board/freescale/imx8qm_mek/Kconfig
create mode 100644 board/freescale/imx8qm_mek/MAINTAINERS
create mode 100644 board/freescale/imx8qm_mek/Makefile
create mode 100644 board/freescale/imx8qm_mek/README
create mode 100644 board/freescale/imx8qm_mek/imx8qm_mek.c
create mode 100644 board/freescale/imx8qm_mek/imximage.cfg
create mode 100644 board/freescale/imx8qm_mek/spl.c
create mode 100644 configs/imx8qm_mek_defconfig
create mode 100644 include/configs/imx8qm_mek.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ad494ec3ef..80009b2c49 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -463,7 +463,9 @@ dtb-$(CONFIG_MX7) += imx7-colibri.dtb \
dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
-dtb-$(CONFIG_ARCH_IMX8) += fsl-imx8qxp-mek.dtb
+dtb-$(CONFIG_ARCH_IMX8) += \
+ fsl-imx8qxp-mek.dtb \
+ fsl-imx8qm-mek.dtb \
dtb-$(CONFIG_ARCH_IMX8M) += fsl-imx8mq-evk.dtb
diff --git a/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
b/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
new file mode 100644
index 0000000000..5d50eb028e
--- /dev/null
+++ b/arch/arm/dts/fsl-imx8qm-mek-u-boot.dtsi
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+&mu {
+ u-boot,dm-spl;
+};
+
+&clk {
+ u-boot,dm-spl;
+};
+
+&iomuxc {
+ u-boot,dm-spl;
+};
+
+&pd_lsio {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio0 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio1 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio2 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio3 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio4 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio5 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio6 {
+ u-boot,dm-spl;
+};
+
+&pd_lsio_gpio7 {
+ u-boot,dm-spl;
+};
+
+&pd_conn {
+ u-boot,dm-spl;
+};
+
+&pd_conn_sdch0 {
+ u-boot,dm-spl;
+};
+
+&pd_conn_sdch1 {
+ u-boot,dm-spl;
+};
+
+&pd_conn_sdch2 {
+ u-boot,dm-spl;
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+};
+
+&gpio1 {
+ u-boot,dm-spl;
+};
+
+&gpio2 {
+ u-boot,dm-spl;
+};
+
+&gpio3 {
+ u-boot,dm-spl;
+};
+
+&gpio4 {
+ u-boot,dm-spl;
+};
+
+&gpio5 {
+ u-boot,dm-spl;
+};
+
+&gpio6 {
+ u-boot,dm-spl;
+};
+
+&gpio7 {
+ u-boot,dm-spl;
+};
+
+&lpuart0 {
+ u-boot,dm-spl;
+};
+
+&usdhc1 {
+ u-boot,dm-spl;
+};
+
+&usdhc2 {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/fsl-imx8qm-mek.dts b/arch/arm/dts/fsl-imx8qm-mek.dts
new file mode 100644
index 0000000000..63908ba6bf
--- /dev/null
+++ b/arch/arm/dts/fsl-imx8qm-mek.dts
@@ -0,0 +1,184 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ */
+
+/dts-v1/;
+
+#include "fsl-imx8qm.dtsi"
+#include "fsl-imx8qm-mek-u-boot.dtsi"
+
+/ {
+ model = "Freescale i.MX8QM MEK";
+ compatible = "fsl,imx8qm-mek", "fsl,imx8qm";
+
+ chosen {
+ bootargs = "console=ttyLP0,115200
earlycon=lpuart32,0x5a060000,115200";
+ stdout-path = &lpuart0;
+ };
+
+ reg_usdhc2_vmmc: usdhc2_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "sw-3p3-sd1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+ off-on-delay = <4800>;
+ enable-active-high;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx8qm-mek {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ SC_P_MCLK_OUT0_AUD_ACM_MCLK_OUT0
0x0600004c
+ SC_P_QSPI1A_DATA1_LSIO_GPIO4_IO25
0x0600004c
+ SC_P_SCU_GPIO0_03_LSIO_GPIO0_IO31
0x0600004c
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD
0x000014a0
+ SC_P_ENET0_MDC_CONN_ENET0_MDC
0x06000020
+ SC_P_ENET0_MDIO_CONN_ENET0_MDIO
0x06000020
+ SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL
0x00000061
+ SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC
0x00000061
+ SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0
0x00000061
+ SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1
0x00000061
+ SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2
0x00000061
+ SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3
0x00000061
+ SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC
0x00000061
+ SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL
0x00000061
+ SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0
0x00000061
+ SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1
0x00000061
+ SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2
0x00000061
+ SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3
0x00000061
+ >;
+ };
+
+ pinctrl_fec2: fec2grp {
+ fsl,pins = <
+ SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD
0x000014a0
+ SC_P_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL
0x00000060
+ SC_P_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC
0x00000060
+ SC_P_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0
0x00000060
+ SC_P_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1
0x00000060
+ SC_P_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2
0x00000060
+ SC_P_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3
0x00000060
+ SC_P_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC
0x00000060
+ SC_P_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL
0x00000060
+ SC_P_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0
0x00000060
+ SC_P_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1
0x00000060
+ SC_P_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2
0x00000060
+ SC_P_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3
0x00000060
+ >;
+ };
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ SC_P_UART0_RX_DMA_UART0_RX
0x06000020
+ SC_P_UART0_TX_DMA_UART0_TX
0x06000020
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ SC_P_EMMC0_CLK_CONN_EMMC0_CLK
0x06000041
+ SC_P_EMMC0_CMD_CONN_EMMC0_CMD
0x00000021
+ SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0
0x00000021
+ SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1
0x00000021
+ SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2
0x00000021
+ SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3
0x00000021
+ SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4
0x00000021
+ SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5
0x00000021
+ SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6
0x00000021
+ SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7
0x00000021
+ SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE
0x00000041
+ SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B
0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21
0x00000021
+ SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22
0x00000021
+ SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07
0x00000021
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ SC_P_USDHC1_CLK_CONN_USDHC1_CLK
0x06000041
+ SC_P_USDHC1_CMD_CONN_USDHC1_CMD
0x00000021
+ SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0
0x00000021
+ SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1
0x00000021
+ SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2
0x00000021
+ SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3
0x00000021
+ SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT
0x00000021
+ >;
+ };
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-txid";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ fsl,rgmii_rxc_dly;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ at803x,eee-disabled;
+ at803x,vddio-1p8v;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ at803x,eee-disabled;
+ at803x,vddio-1p8v;
+ status = "disabled";
+ };
+ };
+};
+
+&lpuart0 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lpuart0>;
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index 4336a8c236..c32f7dbb61 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -32,8 +32,14 @@ config TARGET_IMX8QXP_MEK
select BOARD_LATE_INIT
select IMX8QXP
+config TARGET_IMX8QM_MEK
+ bool "Support i.MX8QM MEK board"
+ select BOARD_LATE_INIT
+ select IMX8QM
+
endchoice
source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/freescale/imx8qm_mek/Kconfig"
endif
diff --git a/board/freescale/imx8qm_mek/Kconfig
b/board/freescale/imx8qm_mek/Kconfig
new file mode 100644
index 0000000000..93d7d5f9c5
--- /dev/null
+++ b/board/freescale/imx8qm_mek/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_IMX8QM_MEK
+
+config SYS_BOARD
+ default "imx8qm_mek"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "imx8qm_mek"
+
+source "board/freescale/common/Kconfig"
+
+endif
diff --git a/board/freescale/imx8qm_mek/MAINTAINERS
b/board/freescale/imx8qm_mek/MAINTAINERS
new file mode 100644
index 0000000000..115830df19
--- /dev/null
+++ b/board/freescale/imx8qm_mek/MAINTAINERS
@@ -0,0 +1,6 @@
+i.MX8QM MEK BOARD
+M: Peng Fan <peng....@nxp.com>
+S: Maintained
+F: board/freescale/imx8qm_mek/
+F: include/configs/imx8qm_mek.h
+F: configs/imx8qm_mek_defconfig
diff --git a/board/freescale/imx8qm_mek/Makefile
b/board/freescale/imx8qm_mek/Makefile
new file mode 100644
index 0000000000..bc9a1260bd
--- /dev/null
+++ b/board/freescale/imx8qm_mek/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2018 NXP
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += imx8qm_mek.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/freescale/imx8qm_mek/README
b/board/freescale/imx8qm_mek/README
new file mode 100644
index 0000000000..c3523801ae
--- /dev/null
+++ b/board/freescale/imx8qm_mek/README
@@ -0,0 +1,57 @@
+U-Boot for the NXP i.MX8QM EVK board
+
+Quick Start
+===========
+
+- Build the ARM Trusted firmware binary
+- Get scfw_tcm.bin and ahab-container.img
+- Build U-Boot
+- Flash the binary into the SD card
+- Boot
+
+Get and Build the ARM Trusted firmware
+======================================
+
+$ git clone https://source.codeaurora.org/external/imx/imx-atf
+$ cd imx-atf/
+$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
+$ make PLAT=imx8qm bl31
+
+Get scfw_tcm.bin and ahab-container.img
+==============================
+
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
+$ chmod +x imx-sc-firmware-1.1.bin
+$ ./imx-sc-firmware-1.1.bin
+$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
+$ chmod +x firmware-imx-8.0.bin
+$ ./firmware-imx-8.0.bin
+
+Copy the following binaries to U-Boot folder:
+
+$ cp imx-atf/build/imx8qm/release/bl31.bin .
+$ cp u-boot/u-boot.bin .
+
+Copy the following firmwares U-Boot folder :
+
+$ cp firmware-imx-7.6/firmware/seco/ahab-container.img .
+$ cp imx-sc-firmware-0.7/mx8qm-mek-scfw-tcm.bin .
+
+Build U-Boot
+============
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make imx8qm_mek_defconfig
+$ make flash.bin
+$ dd if=u-boot.itb of=flash.bin bs=512 seek=1984
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
+
+Boot
+====
+Set Boot switch SW2: 1100.
diff --git a/board/freescale/imx8qm_mek/imx8qm_mek.c
b/board/freescale/imx8qm_mek/imx8qm_mek.c
new file mode 100644
index 0000000000..e69efc4dd6
--- /dev/null
+++ b/board/freescale/imx8qm_mek/imx8qm_mek.c
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2018 NXP
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <environment.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+ (SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+ (SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+ (SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+ SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+ int ret;
+ /* Set UART0 clock root to 80 MHz */
+ sc_pm_clock_rate_t rate = 80000000;
+
+ /* Power up UART0 */
+ ret = sc_pm_set_resource_power_mode(-1, SC_R_UART_0, SC_PM_PW_MODE_ON);
+ if (ret)
+ return ret;
+
+ ret = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate);
+ if (ret)
+ return ret;
+
+ /* Enable UART0 clock root */
+ ret = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false);
+ if (ret)
+ return ret;
+
+ setup_iomux_uart();
+
+ sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5, SC_PM_PW_MODE_ON);
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_DM_GPIO)
+static void board_gpio_init(void)
+{
+ /* TODO */
+}
+#else
+static inline void board_gpio_init(void) {}
+#endif
+
+#if IS_ENABLED(CONFIG_FEC_MXC)
+#include <miiphy.h>
+
+int board_phy_config(struct phy_device *phydev)
+{
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+#endif
+
+void build_info(void)
+{
+ u32 sc_build = 0, sc_commit = 0;
+
+ /* Get SCFW build and commit id */
+ sc_misc_build_info(-1, &sc_build, &sc_commit);
+ if (!sc_build) {
+ printf("SCFW does not support build info\n");
+ sc_commit = 0; /* Display 0 when the build info is not
supported*/
+ }
+ printf("Build: SCFW %x\n", sc_commit);
+}
+
+int checkboard(void)
+{
+ puts("Board: iMX8QM MEK\n");
+
+ build_info();
+ print_bootinfo();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Power up base board */
+ sc_pm_set_resource_power_mode(-1, SC_R_BOARD_R1, SC_PM_PW_MODE_ON);
+
+ board_gpio_init();
+
+ return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+ /* TODO */
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ return 0;
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ env_set("board_name", "MEK");
+ env_set("board_rev", "iMX8QM");
+#endif
+
+ return 0;
+}
diff --git a/board/freescale/imx8qm_mek/imximage.cfg
b/board/freescale/imx8qm_mek/imximage.cfg
new file mode 100644
index 0000000000..7dc6b93eb5
--- /dev/null
+++ b/board/freescale/imx8qm_mek/imximage.cfg
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-mek-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 spl/u-boot-spl.bin 0x00100000
diff --git a/board/freescale/imx8qm_mek/spl.c b/board/freescale/imx8qm_mek/spl.c
new file mode 100644
index 0000000000..95ce9f37e8
--- /dev/null
+++ b/board/freescale/imx8qm_mek/spl.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright 2018 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <dm/uclass.h>
+#include <dm/device.h>
+#include <dm/uclass-internal.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void spl_board_init(void)
+{
+ struct udevice *dev;
+ int offset;
+
+ uclass_find_first_device(UCLASS_MISC, &dev);
+
+ for (; dev; uclass_find_next_device(&dev)) {
+ if (device_probe(dev))
+ continue;
+ }
+
+ offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1, "nxp,imx8-pd");
+ while (offset != -FDT_ERR_NOTFOUND) {
+ lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset),
+ NULL, true);
+ offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset,
+ "nxp,imx8-pd");
+ }
+
+ uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev);
+
+ for (; dev; uclass_find_next_device(&dev)) {
+ if (device_probe(dev))
+ continue;
+ }
+
+ arch_cpu_init();
+
+ board_early_init_f();
+
+ timer_init();
+
+ preloader_console_init();
+
+ puts("Normal Boot\n");
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ /* Just empty function now - can't decide what to choose */
+ debug("%s: %s\n", __func__, name);
+
+ return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+ /* Clear global data */
+ memset((void *)gd, 0, sizeof(gd_t));
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ board_init_r(NULL, 0);
+}
diff --git a/configs/imx8qm_mek_defconfig b/configs/imx8qm_mek_defconfig
new file mode 100644
index 0000000000..238d44d1f5
--- /dev/null
+++ b/configs/imx8qm_mek_defconfig
@@ -0,0 +1,75 @@
+CONFIG_ARM=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_IMX8QM_MEK=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_SPL=y
+CONFIG_NR_DRAM_BANKS=3
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx8qm_mek/imximage.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_LOG=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_CPU=y
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qm-mek"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_MXC_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPL_TINY_MEMSET=y
+# CONFIG_EFI_LOADER is not set
diff --git a/include/configs/imx8qm_mek.h b/include/configs/imx8qm_mek.h
new file mode 100644
index 0000000000..02c5d1c054
--- /dev/null
+++ b/include/configs/imx8qm_mek.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#ifndef __IMX8QM_MEK_H
+#define __IMX8QM_MEK_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_TEXT_BASE 0x0
+#define CONFIG_SPL_MAX_SIZE (124 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x800
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 0
+
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK 0x013E000
+#define CONFIG_SPL_BSS_START_ADDR 0x00128000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x1000 /* 4 KB */
+#define CONFIG_SYS_SPL_MALLOC_START 0x00120000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3000 /* 12 KB */
+#define CONFIG_SERIAL_LPUART_BASE 0x5a060000
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_MALLOC_F_ADDR 0x00120000
+
+#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
+
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
+
+#define CONFIG_OF_EMBED
+#endif
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+#undef CONFIG_CMD_EXPORTENV
+#undef CONFIG_CMD_IMPORTENV
+#undef CONFIG_CMD_IMLS
+
+#undef CONFIG_CMD_CRC32
+#undef CONFIG_BOOTM_NETBSD
+
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define USDHC1_BASE_ADDR 0x5B010000
+#define USDHC2_BASE_ADDR 0x5B020000
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=Image\0" \
+ "panel=NULL\0" \
+ "console=ttyLP0,${baudrate} earlycon=lpuart32,0x5a060000,${baudrate}\0"
\
+ "fdt_addr=0x83000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "boot_fdt=try\0" \
+ "fdt_file=fsl-imx8qxp-mek.dtb\0" \
+ "initrd_addr=0x83800000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
+ "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr}
${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "echo wait for boot; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${loadaddr} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "booti; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR 0x80280000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
+
+/* Default environment is in SD */
+#define CONFIG_ENV_SIZE 0x1000
+#define CONFIG_ENV_OFFSET (64 * SZ_64K)
+#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board */
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
+#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+#define PHYS_SDRAM_1 0x80000000
+#define PHYS_SDRAM_2 0x880000000
+#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
+#define PHYS_SDRAM_2_SIZE 0x100000000 /* 4 GB */
+
+/* Serial */
+#define CONFIG_BAUDRATE 115200
+
+/* Monitor Command Prompt */
+#define CONFIG_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_CBSIZE 2048
+#define CONFIG_SYS_MAXARGS 64
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 8000000 /* 8MHz */
+
+/* Networking */
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define FEC_QUIRK_ENET_MAC
+
+#endif /* __IMX8QM_MEK_H */
--
2.14.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
