Instead of compiling just a few files from the root Makefile, rework the MTD Makefile tree to take into account SPL's needs.
Signed-off-by: Miquel Raynal <[email protected]> --- drivers/Makefile | 6 +----- drivers/mtd/Makefile | 44 ++++++++++++++++++++++++++------------- drivers/mtd/nand/Makefile | 4 ++++ 3 files changed, 35 insertions(+), 19 deletions(-) diff --git a/drivers/Makefile b/drivers/Makefile index e7c93875bb..03aa26535c 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -6,12 +6,11 @@ obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/ obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/ obj-$(CONFIG_$(SPL_TPL_)LED) += led/ obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/ -obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/ +obj-y += mtd/ obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/ obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/ obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/ obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/ -obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/ obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/ obj-$(CONFIG_$(SPL_TPL_)TIMER) += timer/ obj-$(CONFIG_$(SPL_TPL_)VIRTIO) += virtio/ @@ -33,9 +32,6 @@ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/ obj-$(CONFIG_SPL_POWER_DOMAIN) += power/domain/ obj-$(CONFIG_SPL_DM_RESET) += reset/ -obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/ -obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/ -obj-$(CONFIG_SPL_UBI) += mtd/ubispl/ obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/ diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile index fc4c7e0d1f..fd4c6687cb 100644 --- a/drivers/mtd/Makefile +++ b/drivers/mtd/Makefile @@ -3,24 +3,40 @@ # (C) Copyright 2000-2007 # Wolfgang Denk, DENX Software Engineering, [email protected]. -obj-$(CONFIG_MTD) += mtdcore.o mtd_uboot.o -obj-$(CONFIG_DM_MTD) += mtd-uclass.o -obj-$(CONFIG_MTD_PARTITIONS) += mtdpart.o -obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o -obj-$(CONFIG_ALTERA_QSPI) += altera_qspi.o -obj-$(CONFIG_FLASH_CFI_DRIVER) += cfi_flash.o -obj-$(CONFIG_FLASH_CFI_MTD) += cfi_mtd.o -obj-$(CONFIG_FLASH_CFI_LEGACY) += jedec_flash.o -obj-$(CONFIG_MW_EEPROM) += mw_eeprom.o -obj-$(CONFIG_FLASH_PIC32) += pic32_flash.o -obj-$(CONFIG_ST_SMI) += st_smi.o -obj-$(CONFIG_STM32_FLASH) += stm32_flash.o -obj-$(CONFIG_RENESAS_RPC_HF) += renesas_rpc_hf.o +mtd-$(CONFIG_MTD) += mtdcore.o mtd_uboot.o +mtd-$(CONFIG_DM_MTD) += mtd-uclass.o +mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart.o +mtd-$(CONFIG_MTD_CONCAT) += mtdconcat.o +mtd-$(CONFIG_ALTERA_QSPI) += altera_qspi.o +mtd-$(CONFIG_FLASH_CFI_DRIVER) += cfi_flash.o +mtd-$(CONFIG_FLASH_CFI_MTD) += cfi_mtd.o +mtd-$(CONFIG_FLASH_CFI_LEGACY) += jedec_flash.o +mtd-$(CONFIG_MW_EEPROM) += mw_eeprom.o +mtd-$(CONFIG_FLASH_PIC32) += pic32_flash.o +mtd-$(CONFIG_ST_SMI) += st_smi.o +mtd-$(CONFIG_STM32_FLASH) += stm32_flash.o +mtd-$(CONFIG_RENESAS_RPC_HF) += renesas_rpc_hf.o -# SPL will manually build the files it needs +# U-Boot build ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),) + +ifneq ($(mtd-y),) +obj-y += mtd.o +endif obj-y += nand/ obj-y += onenand/ obj-y += spi/ obj-$(CONFIG_MTD_UBI) += ubi/ + +#SPL/TPL build +else + +ifneq ($(mtd-y),) +obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd.o +endif +obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += nand/ +obj-$(CONFIG_SPL_ONENAND_SUPPORT) += onenand/ +obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += spi/ +obj-$(CONFIG_SPL_UBI) += ubispl/ + endif diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index e5849dc02a..96e186600a 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -1,6 +1,10 @@ # SPDX-License-Identifier: GPL-2.0+ +ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),) nandcore-objs := core.o bbt.o obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o obj-$(CONFIG_MTD_RAW_NAND) += raw/ obj-$(CONFIG_MTD_SPI_NAND) += spi/ +else +obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += raw/ +endif -- 2.19.1 _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
