Hi Jonathan,
On Wed, Jul 11, 2018 at 3:11 AM Jonathan Gray <j...@jsg.id.au> wrote:
>
> On Tue, Jul 10, 2018 at 10:37:19PM +0200, Belisko Marek wrote:
> > Hello,
> >
> > I'm trying to use u-boot on CM3 (which contains eMMC) to boot kernel.
> > I'm using u-boot 2018.05 and it can start fine like:
> > U-Boot 2018.05 (Jul 10 2018 - 20:32:05 +0000)
> >
> > DRAM: 948 MiB
> > RPI Compute Module 3 (0xa220a0)
> > MMC: sdhci@7e300000: 0
> > Loading Environment from FAT... unable to select a mode
> > ** No partition table - mmc 0 **
> > Failed (-5)
> > In: serial
> > Out: vidconsole
> > Err: vidconsole
> > Net: No ethernet found.
> > starting USB...
> > USB0: scanning bus 0 for devices... 1 USB Device(s) found
> > scanning usb for storage devices... 0 Storage Device(s) found
> > Hit any key to stop autoboot: 0
> > U-Boot>
> > U-Boot>
> > U-Boot>
> > U-Boot> mmc info
> > Device: sdhci@7e300000
> > Manufacturer ID: 15
> > OEM: 100
> > Name: 4FPD3
> > Bus Speed: 52000000
> > Mode : MMC legacy
> > Rd Block Len: 512
> > MMC version 5.0
> > High Capacity: Yes
> > Capacity: 3.6 GiB
> > Bus Width: 1-bit
> > Erase Group Size: 512 KiB
> > HC WP Group Size: 8 MiB
> > User Capacity: 3.6 GiB WRREL
> > Boot Capacity: 4 MiB ENH
> > RPMB Capacity: 512 KiB ENH
> > U-Boot> mmc part
> > ## Unknown partition table type 0
> > U-Boot> mmc read $loadaddr 0 2
> >
> > but reading from eMMC fails with:
> >
> > MMC read: dev # 0, block # 0, count 2 ... 0 blocks read: ERROR
> >
> > so it looks like eMMC is not properly working with CM3 in this
> > version? Any ideas what to check to have it working before I dig to
> > debugging session ;). Thanks.
>
> You should give 2018.07 a try, which includes a change for a problem
> reported by someone with a CM3.
>
> commit 79fd08f7456c7d12b04ef39e51d84d9981599c3a
> Author: Alexander Graf <ag...@suse.de>
> Date: Wed May 23 22:24:51 2018 +0200
>
> mmc: Unirqify bcm2835_sdhost and fix writes
>
> The bcm2835 sdhost driver has a problem with "write multiple" commands.
> It seems to boil down to the fact that the controller dislikes its FIFO
> to get drained at the end of a block when a write multiple blocks command
> is in flight.
>
> The easy fix is to simply get rid of all the IRQ driven logic and make
> the driver push as much data into the FIFO as it can. That way we never
> drain and we never run into the problem.
>
> Reported-by: Jan Leonhardt <j...@cyberdesigner.net>
> Signed-off-by: Alexander Graf <ag...@suse.de>
>
> drivers/mmc/bcm2835_sdhost.c | 265
> ++++++++++--------------------------------------------
> 1 file changed, 47 insertions(+), 218 deletions(-)
tried but looks like result is same:
U-Boot 2018.07-dirty (Jul 11 2018 - 03:14:31 +0000)
DRAM: 948 MiB
RPI Compute Module 3 (0xa220a0)
MMC: sdhci@7e300000: 0
Loading Environment from FAT... ** No partition table - mmc 0 **
Failed (-5)
In: serial
Out: vidconsole
Err: vidconsole
Net: No ethernet found.
starting USB...
USB0: scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
U-Boot>
U-Boot> mmc dev
unable to select a mode
switch to partitions #0, OK
mmc0(part 0) is current device
U-Boot> mmc info
Device: sdhci@7e300000
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Bus Speed: 52000000
Mode : MMC legacy
Rd Block Len: 512
MMC version 5.0
High Capacity: Yes
Capacity: 3.6 GiB
Bus Width: 1-bit
Erase Group Size: 512 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.6 GiB WRREL
Boot Capacity: 4 MiB ENH
RPMB Capacity: 512 KiB ENH
U-Boot> mmc part
## Unknown partition table type 0
U-Boot> mmc read $loadaddr 0 2
MMC read: dev # 0, block # 0, count 2 ... 0 blocks read: ERROR
U-Boot>
Thanks and BR,
marek
--
as simple and primitive as possible
-------------------------------------------------
Marek Belisko - OPEN-NANDRA
Freelance Developer
Ruska Nova Ves 219 | Presov, 08005 Slovak Republic
Tel: +421 915 052 184
skype: marekwhite
twitter: #opennandra
web: http://open-nandra.com
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
