Ooops I meant https://patchwork.ozlabs.org/patch/895969/ here.
This one I guess is for Albert or Michal. -Alexey On Mon, 2018-05-28 at 12:33 +0300, Alexey Brodkin wrote: > Hi gents, > > On Sun, 2018-04-08 at 00:27 +0300, Tuomas Tynkkynen wrote: > > Signed-off-by: Tuomas Tynkkynen <[email protected]> > > --- > > arch/arm/Kconfig | 2 ++ > > drivers/serial/Kconfig | 5 +++++ > > include/configs/xilinx_zynqmp.h | 1 - > > include/configs/zynq-common.h | 2 -- > > scripts/config_whitelist.txt | 1 - > > 5 files changed, 7 insertions(+), 4 deletions(-) > > Not sure who's the right person to review and accept this one. > I'm not the one for sure :) > > -Alexey > > > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig > > index 190f883aa8..44a4471b47 100644 > > --- a/arch/arm/Kconfig > > +++ b/arch/arm/Kconfig > > @@ -776,6 +776,7 @@ config ARCH_ZYNQ > > select CLK > > select SPL_CLK if SPL > > select CLK_ZYNQ > > + imply ARM_DCC > > imply CMD_CLK > > imply FAT_WRITE > > imply CMD_SPL > > @@ -792,6 +793,7 @@ config ARCH_ZYNQMP > > select SPL_BOARD_INIT if SPL > > select SPL_CLK if SPL > > select DM_USB if USB > > + imply ARM_DCC > > imply FAT_WRITE > > > > config TEGRA > > diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig > > index 9387b642b3..41ce6dec8c 100644 > > --- a/drivers/serial/Kconfig > > +++ b/drivers/serial/Kconfig > > @@ -432,6 +432,11 @@ config AR933X_UART > > tree binding to operate, please refer to the document at > > doc/device-tree-bindings/serial/qca,ar9330-uart.txt. > > > > +config ARM_DCC > > + bool "ARM DCC (Debug Communications Channel) serial console support" > > + help > > + Select this to enable a serial port using the ARM JTAG DCC port. > > + > > config ATMEL_USART > > bool "Atmel USART support" > > help > > diff --git a/include/configs/xilinx_zynqmp.h > > b/include/configs/xilinx_zynqmp.h > > index 8c0b5d9c06..312a2a83ff 100644 > > --- a/include/configs/xilinx_zynqmp.h > > +++ b/include/configs/xilinx_zynqmp.h > > @@ -42,7 +42,6 @@ > > #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 0x2000000) > > > > /* Serial setup */ > > -#define CONFIG_ARM_DCC > > #define CONFIG_CPU_ARMV8 > > > > #define CONFIG_SYS_BAUDRATE_TABLE \ > > diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h > > index 554fb66634..699c91d3c5 100644 > > --- a/include/configs/zynq-common.h > > +++ b/include/configs/zynq-common.h > > @@ -32,8 +32,6 @@ > > #define CONFIG_SYS_BAUDRATE_TABLE \ > > {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} > > > > -#define CONFIG_ARM_DCC > > - > > /* Ethernet driver */ > > #if defined(CONFIG_ZYNQ_GEM) > > # define CONFIG_MII > > diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt > > index 30da0122f0..417a978f0a 100644 > > --- a/scripts/config_whitelist.txt > > +++ b/scripts/config_whitelist.txt > > @@ -59,7 +59,6 @@ CONFIG_ARMV7_SECURE_MAX_SIZE > > CONFIG_ARMV7_SECURE_RESERVE_SIZE > > CONFIG_ARMV8_SWITCH_TO_EL1 > > CONFIG_ARM_ARCH_CP15_ERRATA > > -CONFIG_ARM_DCC > > CONFIG_ARM_FREQ > > CONFIG_ARM_GIC_BASE_ADDRESS > > CONFIG_ARM_PL180_MMCI_BASE _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
