Hi Jun, On Mon, May 7, 2018 at 1:03 PM, Jagan Teki <ja...@amarulasolutions.com> wrote: > This series rework of previous version where it removes legacy > usb phy handling and added phy driver on generic-phy framework. > > Current implementation phy driver is unable to get pinctrl, clock > and reset details from DT since the dm code on these will add it future. > > Changes for v7: > - rebase on master > > Changes for v6: > - Create private config for passing through driver_data instead > directly passing musb_config. This make room for adding new > configs in coming patches. > - memset to pdata in musb-new/sunxi.c > > Changes for v5: > - Rework of previous series > - Used driver_data on sunxi.c since dt supported > - tested on bpi-m2-plus, orangepi_pc2/prime, bananapi-m64 > > Changes for v4: > - Rework of previous series > - Add Allwinner sun4i USB PHY driver > - Drop legacy arch/arm/mach-sunxi/usb_phy.c and related code > > Chen-Yu Tsai (1): > sunxi: clock: Fix OHCI clock gating for H3/H5 > > Jagan Teki (33): > usb: sunxi: Simplify ccm reg base code > musb: sunxi: Add proper macros instead of numericals > musb: sunxi: Use simple way to fill musb_hdrc pdata > musb: sunxi: Add fifo config > sunxi: clock: Fix clock gating for H3/H5/A64 > musb: sunxi: Add OTG device clkgate and reset for H3/H5 > musb: sunxi: Use BIT instead of numerical shift > musb: sunxi: Add support for H3/H5A64 > phy: Add Allwinner A64 USB PHY driver > phy: sun4i-usb: Add id_detect and vbus_detect ops > phy: sun4i-usb: Add H3/H5 PHY config > phy: sun4i-usb: Add V3S PHY config > phy: sun4i-usb: Add A83T USB PHY config > phy: sun4i-usb: Add A10/A13/A20 PHY config > phy: sun4i-usb: Add A31 PHY config > phy: sun4i-usb: Add A33 USB PHY config > phy: sun4i-usb: Add A23 USB PHY config > device-tree-bindings: phy: Sync sun4i-usb-phy bindings > board: sunxi: Use generic-phy for board_usb_cable_connected > phy: sun4i-usb: Add a sunxi specific function for setting > squelch-detect > usb: sunxi: Switch to use generic-phy > sunxi: Drop legacy usb_phy.c > arm64: allwinner: a64: bananapi-m64: Sync usb_otg node from Linux > configs: bananapi-m64: Enable USB OTG peripheral mode > ARM: dts: sun8i: a83t: Sync usbphy node from Linux > arm64: allwinner: a64: bananapi-m64: Sync usb host nodes from Linux > ARM: dts: sun8i-h3: bananapi-m2-plus: Sync usb otg nodes from Linux > configs: bananapi-m2-plus: Enable USB OTG peripheral mode > arm64: allwinner: h5: orangepi-pc2: Order nodes in alphabetic > arm64: allwinner: h5: orangepi-pc2: Sync usb otg nodes from Linux > configs: orangepi-pc2: Enable USB OTG peripheral mode > arm64: allwinner: h5: orangepi-prime: Sync usb otg nodes from Linux > configs: orangepi-prime: Enable USB OTG peripheral mode > > Jun Nie (1): > sunxi: h3: Sync OTG and HCI nodes from Linux DT
I've verified H3/H5 boards and can you do it from your side? Jagan. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
