> -----Original Message-----
> From: Alexander Graf [mailto:ag...@suse.de]
> Sent: Monday, May 07, 2018 4:59 AM
> To: u-boot@lists.denx.de
> Cc: Heinrich Schuchardt; sch...@suse.de; Greentime Hu; Rick Jian-Zhi Chen(陳
> 建志)
> Subject: Re: [U-Boot] [PATCH v3 0/8] riscv: Enable efi_loader support
>
>
>
> On 23.04.18 07:59, Alexander Graf wrote:
> > We now have RISC-V support in U-Boot - which is great!
> >
> > However, not that we're finally making progress to converge on
> > efi_loader and distro boot for booting on ARM platforms, we really
> > want to make sure there is no technical reason not to do the same on
> > RISC-V as well.
> >
> > So this patch set introduces distro boot and efi_loader support for
> > RISC-V!
> >
> > So far, I've only tested it with the selftest and hello world target
> > in U-Boot, as the number of target binaries to run is still slim. But
> > it should at least give us a good starting point.
>
> Rick, can this go into 2018.07?
>
> Via which tree do you want to push it? I can take it via the efi one or you
> can take
> it if you like ;).
>
>
Yes
I prefer to u-boot-riscv.git
If this can enter main line, I will fetch it
I think you can take it via the efi one. :)
But when I verify the efi flow this days.
I find one issue and still clarify it now.
I find the auto flow can not be disabled from make menuconfig
Following are the experiments I do:
Currently the boot flow will auto scan *.efi file from sd card and tftp server.
If I do not insert sd card and tftp server caple.
The boot message will as below:
U-Boot 2018.03-00351-g1dd246f-dirty (Apr 23 2018 - 15:34:32 +0800)
DRAM: 1 GiB
No arch specific invalidate_icache_all available!
MMC:
Loading Environment from SPI Flash... SF: Detected mx25u1635e with page size
256 Bytes, erase size 4 KiB, total 2 MiB
*** Warning - bad CRC, using default environment
Failed (-5)
In: serial@f0300000
Out: serial@f0300000
Err: serial@f0300000
Net: no alias for ethernet0
Warning: mac@e0100000 (eth0) using random MAC address - 66:7d:d7:be:c0:10
eth0: mac@e0100000
Hit any key to stop autoboot: 0
No MMC device available
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
RISC-V #
Then I think if I don't want enter this auto flow, what can I do ?
1 Remove CONFIG_DISTRO_DEFAULTS=y from nx25-ae250_defconfig
But it still enter auto flow.
2 Add #ifdef CONFIG_DISTRO_DEFAULTS to encapsulate the
CONFIG_EXTRA_ENV_SETTINGS in nx25-ae250.h
And Remove CONFIG_DISTRO_DEFAULTS=y from nx25-ae250_defconfig
And it will NOT enter auto flow
#ifdef CONFIG_DISTRO_DEFAULTS
/* Enable distro boot */
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_addr_r=0x00080000\0" \
"pxefile_addr_r=0x01f00000\0" \
"scriptaddr=0x01f00000\0" \
"fdt_addr_r=0x02000000\0" \
"ramdisk_addr_r=0x02800000\0" \
BOOTENV
#endif
3 Add #ifdef CONFIG_DISTRO_DEFAULTS to encapsulate the
CONFIG_EXTRA_ENV_SETTINGS in nx25-ae250.h
And do NOT Remove CONFIG_DISTRO_DEFAULTS=y from nx25-ae250_defconfig
But disable CONFIG_DISTRO_DEFAULTS from make menuconfig
General setup --->
[ ] Select defaults suitable for booting general purpose Linux
distributions
And it still enter auto flow
Offering this information for you.
Rick
> Alex
CONFIDENTIALITY NOTICE:
This e-mail (and its attachments) may contain confidential and legally
privileged information or information protected from disclosure. If you are not
the intended recipient, you are hereby notified that any disclosure, copying,
distribution, or use of the information contained herein is strictly
prohibited. In this case, please immediately notify the sender by return
e-mail, delete the message (and any accompanying documents) and destroy all
printed hard copies. Thank you for your cooperation.
Copyright ANDES TECHNOLOGY CORPORATION - All Rights Reserved.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
