From: Stefan Agner <[email protected]> Move GPMI and BCH register structs to the driver struct mxs_nand_info in prepartion for device tree support.
Signed-off-by: Stefan Agner <[email protected]> --- drivers/mtd/nand/mxs_nand.c | 32 +++++++++++++++----------------- 1 file changed, 15 insertions(+), 17 deletions(-) diff --git a/drivers/mtd/nand/mxs_nand.c b/drivers/mtd/nand/mxs_nand.c index 8305bf2302..f619a2f139 100644 --- a/drivers/mtd/nand/mxs_nand.c +++ b/drivers/mtd/nand/mxs_nand.c @@ -83,6 +83,9 @@ struct mxs_nand_info { uint8_t marking_block_bad; uint8_t raw_oob_mode; + struct mxs_gpmi_regs *gpmi_regs; + struct mxs_bch_regs *bch_regs; + /* Functions with altered behaviour */ int (*hooked_read_oob)(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops); @@ -296,16 +299,15 @@ static inline int mxs_nand_calc_ecc_layout(struct bch_geometry *geo, /* * Wait for BCH complete IRQ and clear the IRQ */ -static int mxs_nand_wait_for_bch_complete(void) +static int mxs_nand_wait_for_bch_complete(struct mxs_nand_info *nand_info) { - struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; int timeout = MXS_NAND_BCH_TIMEOUT; int ret; - ret = mxs_wait_mask_set(&bch_regs->hw_bch_ctrl_reg, + ret = mxs_wait_mask_set(&nand_info->bch_regs->hw_bch_ctrl_reg, BCH_CTRL_COMPLETE_IRQ, timeout); - writel(BCH_CTRL_COMPLETE_IRQ, &bch_regs->hw_bch_ctrl_clr); + writel(BCH_CTRL_COMPLETE_IRQ, &nand_info->bch_regs->hw_bch_ctrl_clr); return ret; } @@ -403,11 +405,9 @@ static int mxs_nand_device_ready(struct mtd_info *mtd) { struct nand_chip *chip = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(chip); - struct mxs_gpmi_regs *gpmi_regs = - (struct mxs_gpmi_regs *)MXS_GPMI_BASE; uint32_t tmp; - tmp = readl(&gpmi_regs->hw_gpmi_stat); + tmp = readl(&nand_info->gpmi_regs->hw_gpmi_stat); tmp >>= (GPMI_STAT_READY_BUSY_OFFSET + nand_info->cur_chip); return tmp & 1; @@ -704,7 +704,7 @@ static int mxs_nand_ecc_read_page(struct mtd_info *mtd, struct nand_chip *nand, goto rtn; } - ret = mxs_nand_wait_for_bch_complete(); + ret = mxs_nand_wait_for_bch_complete(nand_info); if (ret) { printf("MXS NAND: BCH read timeout\n"); goto rtn; @@ -812,7 +812,7 @@ static int mxs_nand_ecc_write_page(struct mtd_info *mtd, goto rtn; } - ret = mxs_nand_wait_for_bch_complete(); + ret = mxs_nand_wait_for_bch_complete(nand_info); if (ret) { printf("MXS NAND: BCH write timeout\n"); goto rtn; @@ -1037,7 +1037,7 @@ static int mxs_nand_setup_ecc(struct mtd_info *mtd) struct nand_chip *nand = mtd_to_nand(mtd); struct mxs_nand_info *nand_info = nand_get_controller_data(nand); struct bch_geometry *geo = &nand_info->bch_geometry; - struct mxs_bch_regs *bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; + struct mxs_bch_regs *bch_regs = nand_info->bch_regs; uint32_t tmp; int ret = -ENOTSUPP; @@ -1138,10 +1138,6 @@ int mxs_nand_alloc_buffers(struct mxs_nand_info *nand_info) */ int mxs_nand_init(struct mxs_nand_info *info) { - struct mxs_gpmi_regs *gpmi_regs = - (struct mxs_gpmi_regs *)MXS_GPMI_BASE; - struct mxs_bch_regs *bch_regs = - (struct mxs_bch_regs *)MXS_BCH_BASE; int i = 0, j, ret = 0; info->desc = malloc(sizeof(struct mxs_dma_desc *) * @@ -1170,14 +1166,14 @@ int mxs_nand_init(struct mxs_nand_info *info) } /* Reset the GPMI block. */ - mxs_reset_block(&gpmi_regs->hw_gpmi_ctrl0_reg); - mxs_reset_block(&bch_regs->hw_bch_ctrl_reg); + mxs_reset_block(&info->gpmi_regs->hw_gpmi_ctrl0_reg); + mxs_reset_block(&info->bch_regs->hw_bch_ctrl_reg); /* * Choose NAND mode, set IRQ polarity, disable write protection and * select BCH ECC. */ - clrsetbits_le32(&gpmi_regs->hw_gpmi_ctrl1, + clrsetbits_le32(&info->gpmi_regs->hw_gpmi_ctrl1, GPMI_CTRL1_GPMI_MODE, GPMI_CTRL1_ATA_IRQRDY_POLARITY | GPMI_CTRL1_DEV_RESET | GPMI_CTRL1_BCH_MODE); @@ -1211,6 +1207,8 @@ void board_nand_init(void) } memset(nand_info, 0, sizeof(struct mxs_nand_info)); + nand_info->gpmi_regs = (struct mxs_gpmi_regs *)MXS_GPMI_BASE; + nand_info->bch_regs = (struct mxs_bch_regs *)MXS_BCH_BASE; nand = &nand_info->chip; mtd = nand_to_mtd(nand); err = mxs_nand_alloc_buffers(nand_info); -- 2.17.0 _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
