From: Philipp Tomsich <philipp.toms...@theobroma-systems.com>
Throughput tests have shown the sunxi_mmc driver to take over 10s to
read 10MB from a fast eMMC device due to excessive delays in polling
loops.
This commit restructures the main polling loops to use get_timer(...)
to determine whether a (millisecond) timeout has expired. We choose
not to use the wait_bit function, as we don't need interruptability
with ctrl-c and have at least one case where two bits (one for an
error condition and another one for completion) need to be read and
using wait_bit would have not added to the clarity.
The observed speedup in testing on a A31 is greater than 10x (e.g. a
10MB write decreases from 9.302s to 0.884s).
Signed-off-by: Philipp Tomsich <philipp.toms...@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.rip...@bootlin.com>
---
drivers/mmc/sunxi_mmc.c | 27 ++++++++++++++++-----------
1 file changed, 16 insertions(+), 11 deletions(-)
diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c
index 4edb4be46c81..d36c1689e7b1 100644
--- a/drivers/mmc/sunxi_mmc.c
+++ b/drivers/mmc/sunxi_mmc.c
@@ -187,15 +187,16 @@ static int mmc_update_clk(struct sunxi_mmc_priv *priv)
{
unsigned int cmd;
unsigned timeout_msecs = 2000;
+ unsigned long start = get_timer(0);
cmd = SUNXI_MMC_CMD_START |
SUNXI_MMC_CMD_UPCLK_ONLY |
SUNXI_MMC_CMD_WAIT_PRE_OVER;
+
writel(cmd, &priv->reg->cmd);
while (readl(&priv->reg->cmd) & SUNXI_MMC_CMD_START) {
- if (!timeout_msecs--)
+ if (get_timer(start) > timeout_msecs)
return -1;
- udelay(1000);
}
/* clock update sets various irq status bits, clear these */
@@ -276,18 +277,21 @@ static int mmc_trans_data_by_cpu(struct sunxi_mmc_priv
*priv, struct mmc *mmc,
unsigned i;
unsigned *buff = (unsigned int *)(reading ? data->dest : data->src);
unsigned byte_cnt = data->blocksize * data->blocks;
- unsigned timeout_usecs = (byte_cnt >> 8) * 1000;
- if (timeout_usecs < 2000000)
- timeout_usecs = 2000000;
+ unsigned timeout_msecs = byte_cnt >> 8;
+ unsigned long start;
+
+ if (timeout_msecs < 2000)
+ timeout_msecs = 2000;
/* Always read / write data through the CPU */
setbits_le32(&priv->reg->gctrl, SUNXI_MMC_GCTRL_ACCESS_BY_AHB);
+ start = get_timer(0);
+
for (i = 0; i < (byte_cnt >> 2); i++) {
while (readl(&priv->reg->status) & status_bit) {
- if (!timeout_usecs--)
+ if (get_timer(start) > timeout_msecs)
return -1;
- udelay(1);
}
if (reading)
@@ -303,16 +307,16 @@ static int mmc_rint_wait(struct sunxi_mmc_priv *priv,
struct mmc *mmc,
uint timeout_msecs, uint done_bit, const char *what)
{
unsigned int status;
+ unsigned long start = get_timer(0);
do {
status = readl(&priv->reg->rint);
- if (!timeout_msecs-- ||
+ if ((get_timer(start) > timeout_msecs) ||
(status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT)) {
debug("%s timeout %x\n", what,
status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT);
return -ETIMEDOUT;
}
- udelay(1000);
} while (!(status & done_bit));
return 0;
@@ -404,15 +408,16 @@ static int sunxi_mmc_send_cmd_common(struct
sunxi_mmc_priv *priv,
}
if (cmd->resp_type & MMC_RSP_BUSY) {
+ unsigned long start = get_timer(0);
timeout_msecs = 2000;
+
do {
status = readl(&priv->reg->status);
- if (!timeout_msecs--) {
+ if (get_timer(start) > timeout_msecs) {
debug("busy timeout\n");
error = -ETIMEDOUT;
goto out;
}
- udelay(1000);
} while (status & SUNXI_MMC_STATUS_CARD_DATA_BUSY);
}
--
2.14.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
