On Sun, 28 Jan 2018 19:11:42 +0900 Masahiro Yamada <yamada.masah...@socionext.com> wrote:
> Use pr_* log functions from Linux. They can be enabled/disabled
> via CONFIG_LOGLEVEL.
>
> Signed-off-by: Masahiro Yamada <yamada.masah...@socionext.com>
> ---
>
> drivers/mmc/mmc.c | 68
> +++++++++++++++++++++++++++---------------------------- 1 file
> changed, 34 insertions(+), 34 deletions(-)
>
> diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> index 255310a..3a2e3b3 100644
> --- a/drivers/mmc/mmc.c
> +++ b/drivers/mmc/mmc.c
> @@ -213,8 +213,8 @@ static int mmc_select_mode(struct mmc *mmc, enum
> bus_mode mode) mmc->selected_mode = mode;
> mmc->tran_speed = mmc_mode2freq(mmc, mode);
> mmc->ddr_mode = mmc_is_mode_ddr(mode);
> - debug("selecting mode %s (freq : %d MHz)\n",
> mmc_mode_name(mode),
> - mmc->tran_speed / 1000000);
> + pr_debug("selecting mode %s (freq : %d MHz)\n",
> mmc_mode_name(mode),
> + mmc->tran_speed / 1000000);
> return 0;
> }
>
> @@ -457,7 +457,7 @@ ulong mmc_bread(struct blk_desc *block_dev,
> lbaint_t start, lbaint_t blkcnt, }
>
> if (mmc_set_blocklen(mmc, mmc->read_bl_len)) {
> - debug("%s: Failed to set blocklen\n", __func__);
> + pr_debug("%s: Failed to set blocklen\n", __func__);
> return 0;
> }
>
> @@ -465,7 +465,7 @@ ulong mmc_bread(struct blk_desc *block_dev,
> lbaint_t start, lbaint_t blkcnt, cur = (blocks_todo >
> mmc->cfg->b_max) ? mmc->cfg->b_max : blocks_todo;
> if (mmc_read_blocks(mmc, dst, start, cur) != cur) {
> - debug("%s: Failed to read blocks\n",
> __func__);
> + pr_debug("%s: Failed to read blocks\n",
> __func__); return 0;
> }
> blocks_todo -= cur;
> @@ -900,11 +900,11 @@ static int mmc_boot_part_access_chk(struct mmc
> *mmc, unsigned int part_num) forbidden = MMC_CAP(MMC_HS_200);
>
> if (MMC_CAP(mmc->selected_mode) & forbidden) {
> - debug("selected mode (%s) is forbidden for part
> %d\n",
> - mmc_mode_name(mmc->selected_mode), part_num);
> + pr_debug("selected mode (%s) is forbidden for part
> %d\n",
> + mmc_mode_name(mmc->selected_mode),
> part_num); change = true;
> } else if (mmc->selected_mode != mmc->best_mode) {
> - debug("selected mode is not optimal\n");
> + pr_debug("selected mode is not optimal\n");
> change = true;
> }
>
> @@ -1427,7 +1427,7 @@ retry_ssr:
> mmc->ssr.erase_offset = eo * 1000;
> }
> } else {
> - debug("Invalid Allocation Unit Size.\n");
> + pr_debug("Invalid Allocation Unit Size.\n");
> }
>
> return 0;
> @@ -1532,18 +1532,18 @@ void mmc_dump_capabilities(const char *text,
> uint caps) {
> enum bus_mode mode;
>
> - printf("%s: widths [", text);
> + pr_debug("%s: widths [", text);
> if (caps & MMC_MODE_8BIT)
> - printf("8, ");
> + pr_debug("8, ");
> if (caps & MMC_MODE_4BIT)
> - printf("4, ");
> + pr_debug("4, ");
> if (caps & MMC_MODE_1BIT)
> - printf("1, ");
> - printf("\b\b] modes [");
> + pr_debug("1, ");
> + pr_debug("\b\b] modes [");
> for (mode = MMC_LEGACY; mode < MMC_MODES_END; mode++)
> if (MMC_CAP(mode) & caps)
> - printf("%s, ", mmc_mode_name(mode));
> - printf("\b\b]\n");
> + pr_debug("%s, ", mmc_mode_name(mode));
> + pr_debug("\b\b]\n");
> }
> #endif
>
> @@ -1577,7 +1577,7 @@ static int mmc_set_signal_voltage(struct mmc
> *mmc, uint signal_voltage) mmc->signal_voltage = signal_voltage;
> err = mmc_set_ios(mmc);
> if (err)
> - debug("unable to set voltage (err %d)\n", err);
> + pr_debug("unable to set voltage (err %d)\n", err);
>
> return err;
> }
> @@ -1660,10 +1660,10 @@ static int sd_select_mode_and_width(struct
> mmc *mmc, uint card_caps)
> for (w = widths; w < widths + ARRAY_SIZE(widths);
> w++) { if (*w & caps & mwt->widths) {
> - debug("trying mode %s width %d (at
> %d MHz)\n",
> - mmc_mode_name(mwt->mode),
> - bus_width(*w),
> - mmc_mode2freq(mmc,
> mwt->mode) / 1000000);
> + pr_debug("trying mode %s width %d
> (at %d MHz)\n",
> + mmc_mode_name(mwt->mode),
> + bus_width(*w),
> + mmc_mode2freq(mmc,
> mwt->mode) / 1000000);
> /* configure the bus width (card +
> host) */ err = sd_select_bus_width(mmc, bus_width(*w));
> @@ -1686,7 +1686,7 @@ static int sd_select_mode_and_width(struct mmc
> *mmc, uint card_caps) err = mmc_execute_tuning(mmc,
> mwt->tuning);
> if (err) {
> - debug("tuning
> failed\n");
> + pr_debug("tuning
> failed\n"); goto error;
> }
> }
> @@ -1708,7 +1708,7 @@ error:
> }
> }
>
> - printf("unable to select a mode\n");
> + pr_err("unable to select a mode\n");
> return -ENOTSUPP;
> }
>
> @@ -1860,7 +1860,7 @@ static int mmc_select_mode_and_width(struct mmc
> *mmc, uint card_caps) return 0;
>
> if (!mmc->ext_csd) {
> - debug("No ext_csd found!\n"); /* this should enver
> happen */
> + pr_debug("No ext_csd found!\n"); /* this should
> enver happen */ return -ENOTSUPP;
> }
>
> @@ -1870,10 +1870,10 @@ static int mmc_select_mode_and_width(struct
> mmc *mmc, uint card_caps) for_each_supported_width(card_caps &
> mwt->widths, mmc_is_mode_ddr(mwt->mode), ecbw) {
> enum mmc_voltage old_voltage;
> - debug("trying mode %s width %d (at %d
> MHz)\n",
> - mmc_mode_name(mwt->mode),
> - bus_width(ecbw->cap),
> - mmc_mode2freq(mmc, mwt->mode) /
> 1000000);
> + pr_debug("trying mode %s width %d (at %d
> MHz)\n",
> + mmc_mode_name(mwt->mode),
> + bus_width(ecbw->cap),
> + mmc_mode2freq(mmc, mwt->mode) /
> 1000000); old_voltage = mmc->signal_voltage;
> err = mmc_set_lowest_voltage(mmc, mwt->mode,
> MMC_ALL_SIGNAL_VOLTAGE);
> @@ -1914,7 +1914,7 @@ static int mmc_select_mode_and_width(struct mmc
> *mmc, uint card_caps) if (mwt->tuning) {
> err = mmc_execute_tuning(mmc,
> mwt->tuning); if (err) {
> - debug("tuning failed\n");
> + pr_debug("tuning failed\n");
> goto error;
> }
> }
> @@ -2396,12 +2396,12 @@ static int mmc_power_init(struct mmc *mmc)
> ret = device_get_supply_regulator(mmc->dev, "vmmc-supply",
> &mmc->vmmc_supply);
> if (ret)
> - debug("%s: No vmmc supply\n", mmc->dev->name);
> + pr_debug("%s: No vmmc supply\n", mmc->dev->name);
>
> ret = device_get_supply_regulator(mmc->dev, "vqmmc-supply",
> &mmc->vqmmc_supply);
> if (ret)
> - debug("%s: No vqmmc supply\n", mmc->dev->name);
> + pr_debug("%s: No vqmmc supply\n", mmc->dev->name);
> #endif
> #else /* !CONFIG_DM_MMC */
> /*
> @@ -2457,7 +2457,7 @@ static int mmc_power_off(struct mmc *mmc)
> int ret = regulator_set_enable(mmc->vmmc_supply,
> false);
> if (ret) {
> - debug("Error disabling VMMC supply\n");
> + pr_debug("Error disabling VMMC supply\n");
> return ret;
> }
> }
> @@ -2505,7 +2505,7 @@ int mmc_start_init(struct mmc *mmc)
> if (no_card) {
> mmc->has_init = 0;
> #if !defined(CONFIG_SPL_BUILD) ||
> defined(CONFIG_SPL_LIBCOMMON_SUPPORT)
> - printf("MMC: no card present\n");
> + pr_err("MMC: no card present\n");
> #endif
> return -ENOMEDIUM;
> }
> @@ -2532,7 +2532,7 @@ int mmc_start_init(struct mmc *mmc)
> * to use the UHS modes, because we wouldn't be able
> to
> * recover from an error during the UHS
> initialization. */
> - debug("Unable to do a full power cycle. Disabling
> the UHS modes for safety\n");
> + pr_debug("Unable to do a full power cycle. Disabling
> the UHS modes for safety\n"); uhs_en = false;
> mmc->host_caps &= ~UHS_CAPS;
> err = mmc_power_on(mmc);
> @@ -2629,7 +2629,7 @@ int mmc_init(struct mmc *mmc)
> if (!err)
> err = mmc_complete_init(mmc);
> if (err)
> - printf("%s: %d, time %lu\n", __func__, err,
> get_timer(start));
> + pr_info("%s: %d, time %lu\n", __func__, err,
> get_timer(start));
> return err;
> }
Reviewed-by: Lukasz Majewski <lu...@denx.de>
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de
pgpxcsT8Cp2Wu.pgp
Description: OpenPGP digital signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
