This series adds the missing bits to enable the UHS and HS200 modes
for the TI platforms.
Enabling support for high speed modes on omap5 requires implementing:
* io signal voltage selection
* tuning support
* pin configuration (IO delays)
The few last patches enable the high speed modes for the DRA7 platforms and
also take care of disabling those modes in the dts for the platforms that
cannot support either the UHS or the HS200 because the voltage regulators
on board would not allow using those modes (not a SOC limitation).
With this in place we observe significant improvements in the performances:
on a DRA72 evm:
eMMC HS200: 124 MB/s
eMMC DDR52: 78 MB/s
sd SDR104: 71 MB/s
sd SDR50: 44 MB/s
For the record, the original performances were:
SD High speed: 18 MB/s
MMC High speed: 18 MB/s
This series has been tested on:
* DRA71-evm
* DRA72-evm
* DRA7x-evm
* DRA76-evm
* AM57x-evm
* Beaglebone Black (dt and non-dt)
changes since v1:
- rebased on top of u-boot/master
- enable the H200 and UHS support in the defconfigs of the DRA7 platforms
Jean-Jacques Hiblot (9):
mmc: omap_hsmmc: Reduce the max timeout for reset controller fsm
mmc: omap_hsmmc: allow the simple HS modes to use the default pinctrl
mmc: omap_hsmmc: update mmc->clock with the actual bus speed
mmc: omap_hsmmc: implement send_init_stream callback
mmc: omap_hsmmc: add signal voltage selection support
ARM: dts: dra7: Add supported MMC/SD modes in MMC dt nodes
dts: am57xx-beagle-x15: disable UHS and HS200 support
dts: am57xx-idk: disable HS200 support
configs: dra7xx_evm/dra7xx_hs_evm: Enable MMC HS200 and SD UHS support
Kishon Vijay Abraham I (15):
mmc: omap_hsmmc: cleanup clock configuration
mmc: omap_hsmmc: cleanup omap_hsmmc_set_ios
mmc: omap_hsmmc: add support to set default io voltage
mmc: omap_hsmmc: set MMC mode in the UHSMS bit field
mmc: omap_hsmmc: Enable DDR mode support
mmc: omap_hsmmc: Add tuning support
mmc: omap_hsmmc: Workaround for errata id i802
mmc: omap_hsmmc: use mmc_of_parse to populate mmc_config
ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot
mmc: omap_hsmmc: Add support to set IODELAY values
mmc: omap_hsmmc: Add support to get pinctrl values and max frequency
for different hw revisions
mmc: omap_hsmmc: allow mmc clock to be gated
ARM: OMAP5: set mmc clock frequency to 192MHz
ARM: dts: DRA7: use new dra7-specific compatible string
ARM: DRA7x/AM57x: Add MMC/SD fixups for rev1.0 and rev 1.1
arch/arm/dts/am57xx-beagle-x15.dts | 6 +
arch/arm/dts/am57xx-idk-common.dtsi | 2 +
arch/arm/dts/dra7.dtsi | 22 +-
arch/arm/include/asm/arch-omap5/clock.h | 2 +-
arch/arm/include/asm/arch-omap5/dra7xx_iodelay.h | 3 +
arch/arm/include/asm/arch-omap5/sys_proto.h | 7 +
arch/arm/include/asm/omap_mmc.h | 59 +-
arch/arm/mach-omap2/omap5/dra7xx_iodelay.c | 30 +
arch/arm/mach-omap2/omap5/hw_data.c | 10 +-
board/ti/am57xx/board.c | 30 +
board/ti/dra7xx/evm.c | 29 +
configs/dra7xx_evm_defconfig | 3 +
configs/dra7xx_hs_evm_defconfig | 3 +
drivers/mmc/omap_hsmmc.c | 948 +++++++++++++++++++++--
include/configs/am57xx_evm.h | 2 -
include/configs/dra7xx_evm.h | 2 -
16 files changed, 1085 insertions(+), 73 deletions(-)
--
1.9.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
