On Fri, Dec 8, 2017 at 8:31 AM, Jagan Teki <jagannadh.t...@gmail.com> wrote: > On Fri, Dec 8, 2017 at 7:59 AM, Chen-Yu Tsai <w...@csie.org> wrote: >> On Fri, Dec 8, 2017 at 1:01 AM, Jagan Teki <jagannadh.t...@gmail.com> wrote: >>> On Thu, Dec 7, 2017 at 6:30 PM, Chen-Yu Tsai <w...@csie.org> wrote: >>>> The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry >>>> Pi B+ form factor single board computer based on the Allwinner H3 SoC. >>>> The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes >>>> and connectors are in the exact same position as on the Raspberry Pi B+. >>>> >>>> Raspberry Pi B+ like peripherals supported on this board include: >>>> >>>> - Power input through micro-USB connector (without USB OTG) >>>> - Native 100 Mbps ethernet using the internal PHY, as opposed to >>>> USB-based on the RPi >>>> - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to >>>> being connected through a USB 2.0 hub on the RPi >>>> - TV and audio output on a 3.5mm TRRS jack >>>> - HDMI output >>>> - Micro-SD card slot >>>> - Standard RPi B+ GPIO header, with the standard peripherals routed to >>>> the same pins. >>>> >>>> * 5V, 3.3V power, and ground >>>> * I2C0 on the H3 is routed to I2C1 pins on the RPi header >>>> * I2C1 on the H3 is routed to I2C0 pins on the RPi header >>>> * UART1 on the H3 is routed to UART0 pins on the RPi header >>>> * SPI0 on the H3 is routed to SPI0 pins on the RPi header, >>>> with GPIO pin PA17 replacing the missing Chip Select 1 >>>> * I2S1 on the H3 is routed to PCM pins on the RPi header >>>> >>>> - Additional peripherals from the H3 are available on different pins. >>>> These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3 >>>> >>>> In addition, there are a number of new features: >>>> >>>> - Console UART header >>>> - Consumer IR receiver >>>> - Camera interface (not compatible with RPi) >>>> - Onboard microphone >>>> - eMMC expansion module port >>>> - Heatsink mounting holes >>>> >>>> This patch adds defconfig and dts files for this board. The dts file is >>>> the same as the one submitted for inclusion in Linux, with some minor >>>> revisions to match the dtsi file and old EMAC bindings in U-boot. >>>> >>>> Since the OTG controller is wired to a USB host port, and the H3 has >>>> proper USB hosts to handle host mode, the MUSB driver is not enabled. >>>> >>>> Signed-off-by: Chen-Yu Tsai <w...@csie.org> >>>> --- >>>> arch/arm/dts/Makefile | 1 + >>>> arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts | 180 >>>> ++++++++++++++++++++++++++ >>>> board/sunxi/MAINTAINERS | 5 + >>>> configs/libretech_all_h3_cc_h3_defconfig | 19 +++ >>>> 4 files changed, 205 insertions(+) >>>> create mode 100644 arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts >>>> create mode 100644 configs/libretech_all_h3_cc_h3_defconfig >>>> >>>> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile >>>> index f54adb21847a..0aba72d3a72f 100644 >>>> --- a/arch/arm/dts/Makefile >>>> +++ b/arch/arm/dts/Makefile >>>> @@ -320,6 +320,7 @@ dtb-$(CONFIG_MACH_SUN8I_A83T) += \ >>>> dtb-$(CONFIG_MACH_SUN8I_H3) += \ >>>> sun8i-h2-plus-orangepi-zero.dtb \ >>>> sun8i-h3-bananapi-m2-plus.dtb \ >>>> + sun8i-h3-libretech-all-h3-cc.dtb \ >>>> sun8i-h3-orangepi-2.dtb \ >>>> sun8i-h3-orangepi-lite.dtb \ >>>> sun8i-h3-orangepi-one.dtb \ >>>> diff --git a/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts >>>> b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts >>>> new file mode 100644 >>>> index 000000000000..97b993f636f9 >>>> --- /dev/null >>>> +++ b/arch/arm/dts/sun8i-h3-libretech-all-h3-cc.dts >>>> @@ -0,0 +1,180 @@ >>>> +/* >>>> + * Copyright (C) 2017 Chen-Yu Tsai <w...@csie.org> >>>> + * >>>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT) >>>> + */ >>> >>> Why can't we use Linux license? since we always sync dts files from Linux. >> >> This IS the same license we use for dts files in the Linux kernel. >> We want all projects to be able to use them. It wouldn't make sense >> to have BSD licensed projects to include GPL-only files, now would >> it? > > Reviewed-by: Jagan Teki <ja...@amarulasolutions.com>
Applied to u-boot-sunxi/next _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot
