Signed-off-by: Dmitry Korunov <desse...@gmail.com>
---
Changes for v2:
- removed surplus spaces
- added the board description
Changes for v3:
- excluded already merged *.dtsi files
- updated device tree file to appropriate master branch
arch/arm/dts/bcm2835-rpi-zero-w.dts | 26 ++++++++++++++++++++++++++
arch/arm/mach-bcm283x/Kconfig | 16 ++++++++++++++++
board/raspberrypi/rpi/rpi.c | 5 +++++
configs/rpi_0_w_defconfig | 28 ++++++++++++++++++++++++++++
include/configs/rpi.h | 2 +-
5 files changed, 76 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/bcm2835-rpi-zero-w.dts
create mode 100644 configs/rpi_0_w_defconfig
diff --git a/arch/arm/dts/bcm2835-rpi-zero-w.dts
b/arch/arm/dts/bcm2835-rpi-zero-w.dts
new file mode 100644
index 0000000..7817054
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-zero-w.dts
@@ -0,0 +1,26 @@
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+ model = "Raspberry Pi Zero W";
+
+ leds {
+ act {
+ gpios = <&gpio 47 0>;
+ };
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig
index 69f7a46..a78239d 100644
--- a/arch/arm/mach-bcm283x/Kconfig
+++ b/arch/arm/mach-bcm283x/Kconfig
@@ -44,6 +44,22 @@ config TARGET_RPI
This option creates a build targetting the ARM1176 ISA.
select BCM2835
+config TARGET_RPI_0_W
+ bool "Raspberry Pi Zero W"
+ help
+ Support for all ARM1176-/BCM2835-based Raspberry Pi variants, such as
+ the RPi Zero model W.
+
+ This option assumes the VideoCore firmware is configured to use the
+ mini UART (rather than PL011) for the serial console. This is the
+ default on the RPi Zero W. To enable the UART console, the following
+ non-default option must be present in config.txt: enable_uart=1.
+ This is required for U-Boot to operate correctly, even if you only
+ care about the HDMI/usbkbd console.
+
+ This option creates a build targetting the ARMv7/AArch32 ISA.
+ select BCM2835
+
config TARGET_RPI_2
bool "Raspberry Pi 2"
help
diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c
index 530f149..3b7a54f 100644
--- a/board/raspberrypi/rpi/rpi.c
+++ b/board/raspberrypi/rpi/rpi.c
@@ -105,6 +105,11 @@ static const struct rpi_model rpi_models_new_scheme[] = {
DTB_DIR "bcm2835-rpi-zero.dtb",
false,
},
+ [0xC] = {
+ "Zero W",
+ DTB_DIR "bcm2835-rpi-zero-w.dtb",
+ false,
+ },
};
static const struct rpi_model rpi_models_old_scheme[] = {
diff --git a/configs/rpi_0_w_defconfig b/configs/rpi_0_w_defconfig
new file mode 100644
index 0000000..092f378
--- /dev/null
+++ b/configs/rpi_0_w_defconfig
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_ARCH_BCM283X=y
+CONFIG_TARGET_RPI_0_W=y
+CONFIG_DEFAULT_DEVICE_TREE="bcm2835-rpi-zero-w"
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SYS_PROMPT="U-Boot> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_BCM2835=y
+CONFIG_DM_ETH=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_DM_VIDEO=y
+CONFIG_SYS_WHITE_ON_BLACK=y
+CONFIG_CONSOLE_SCROLL_LINES=10
+CONFIG_PHYS_TO_BUS=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/include/configs/rpi.h b/include/configs/rpi.h
index c499b45..cab8661 100644
--- a/include/configs/rpi.h
+++ b/include/configs/rpi.h
@@ -76,7 +76,7 @@
#endif
/* Console UART */
-#ifdef CONFIG_BCM2837
+#if defined (CONFIG_BCM2837) || defined(CONFIG_TARGET_RPI_0_W)
#define CONFIG_BCM283X_MU_SERIAL
#else
#define CONFIG_PL01X_SERIAL
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
