From: Jagan Teki <ja...@openedev.com>
(1) Enable DM_ETH
(2) Droped board_eth_init
Signed-off-by: Jagan Teki <ja...@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.este...@nxp.com>
---
arch/arm/cpu/armv7/mx6/Kconfig | 1 +
board/freescale/mx6sabresd/mx6sabresd.c | 45 ++-------------------------------
2 files changed, 3 insertions(+), 43 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index d1ba801..f4c8c39 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -214,6 +214,7 @@ config TARGET_MX6SABRESD
select BOARD_LATE_INIT
select OF_CONTROL
select DM
+ select DM_ETH
select DM_GPIO
select DM_MMC
select DM_REGULATOR
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c
b/board/freescale/mx6sabresd/mx6sabresd.c
index 688b326..7eab021 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -17,7 +17,6 @@
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/video.h>
#include <miiphy.h>
-#include <netdev.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
@@ -33,9 +32,6 @@ DECLARE_GLOBAL_DATA_PTR;
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
@@ -60,37 +56,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-static iomux_v3_cfg_t const enet_pads[] = {
- IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
MUX_PAD_CTRL(ENET_PAD_CTRL)),
- /* AR8031 PHY Reset */
- IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_iomux_enet(void)
-{
- SETUP_IOMUX_PADS(enet_pads);
-
- /* Reset AR8031 PHY */
- gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
- mdelay(10);
- gpio_set_value(IMX_GPIO_NR(1, 25), 1);
- udelay(100);
-}
-
static iomux_v3_cfg_t const ecspi1_pads[] = {
IOMUX_PADS(PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
IOMUX_PADS(PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
@@ -383,14 +348,6 @@ int overwrite_console(void)
return 1;
}
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
- setup_pcie();
-
- return cpu_eth_init(bis);
-}
-
int board_early_init_f(void)
{
setup_iomux_uart();
@@ -414,6 +371,8 @@ int board_init(void)
else
setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
+ setup_pcie();
+
return 0;
}
--
1.9.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
