This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address on
serial flash and environment address.
Signed-off-by: Alison Wang <alison.w...@nxp.com>
---
Changes:
- Update the comments.
arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 8 ++++----
include/configs/ls1043a_common.h | 12 ++++++------
include/configs/ls1043aqds.h | 10 +++++-----
include/configs/ls1043ardb.h | 8 ++++----
4 files changed, 19 insertions(+), 19 deletions(-)
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index 4c16c4c..82c76e2 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -163,11 +163,11 @@ endchoice
config SYS_LS_PPA_FW_ADDR
hex "Address of PPA firmware loading from"
depends on FSL_LS_PPA
- default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
+ default 0x40400000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
default 0x580a00000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A
- default 0x60500000 if SYS_LS_PPA_FW_IN_XIP
- default 0x500000 if SYS_LS_PPA_FW_IN_MMC
- default 0x500000 if SYS_LS_PPA_FW_IN_NAND
+ default 0x60400000 if SYS_LS_PPA_FW_IN_XIP
+ default 0x400000 if SYS_LS_PPA_FW_IN_MMC
+ default 0x400000 if SYS_LS_PPA_FW_IN_NAND
help
If the PPA firmware locate at XIP flash, such as NOR or
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
index e269248..05419fe 100644
--- a/include/configs/ls1043a_common.h
+++ b/include/configs/ls1043a_common.h
@@ -208,20 +208,20 @@
#define CONFIG_SYS_FM_MURAM_SIZE 0x60000
#ifdef CONFIG_NAND_BOOT
-/* Store Fman ucode at offeset 0x160000(11 blocks). */
+/* Store Fman ucode at offeset 0x900000(72 blocks). */
#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_FMAN_FW_ADDR (11 *
CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_FMAN_FW_ADDR (72 *
CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
/*
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image
is
* about 1MB (2040 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 2080(0x820).
+ * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800).
*/
#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800)
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x40900000
#define CONFIG_ENV_SPI_BUS 0
#define CONFIG_ENV_SPI_CS 0
#define CONFIG_ENV_SPI_MAX_HZ 1000000
@@ -229,7 +229,7 @@
#else
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
/* FMan fireware Pre-load address */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x60300000
+#define CONFIG_SYS_FMAN_FW_ADDR 0x60900000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
diff --git a/include/configs/ls1043aqds.h b/include/configs/ls1043aqds.h
index b14e944..04d74ac 100644
--- a/include/configs/ls1043aqds.h
+++ b/include/configs/ls1043aqds.h
@@ -12,7 +12,7 @@
#if defined(CONFIG_NAND_BOOT) || defined(CONFIG_SD_BOOT)
#define CONFIG_SYS_TEXT_BASE 0x82000000
#elif defined(CONFIG_QSPI_BOOT)
-#define CONFIG_SYS_TEXT_BASE 0x40010000
+#define CONFIG_SYS_TEXT_BASE 0x40100000
#else
#define CONFIG_SYS_TEXT_BASE 0x60100000
#endif
@@ -413,20 +413,20 @@ unsigned long get_board_ddr_clk(void);
#ifdef CONFIG_NAND_BOOT
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET (24 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_QSPI_BOOT)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
-#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_OFFSET 0x300000 /* 3MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#else
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE +
0x200000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE +
0x300000)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x20000
#endif
diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
index 5e570cd..a162378 100644
--- a/include/configs/ls1043ardb.h
+++ b/include/configs/ls1043ardb.h
@@ -235,15 +235,15 @@
#if defined(CONFIG_NAND_BOOT)
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_ENV_OFFSET (24 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SD_BOOT)
-#define CONFIG_ENV_OFFSET (1024 * 1024)
+#define CONFIG_ENV_OFFSET (3 * 1024 * 1024)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE +
0x200000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE +
0x300000)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x20000
#endif
@@ -281,7 +281,7 @@
!defined(CONFIG_QSPI_BOOT)
#define CONFIG_U_QE
#endif
-#define CONFIG_SYS_QE_FW_ADDR 0x60600000
+#define CONFIG_SYS_QE_FW_ADDR 0x60940000
#endif
/* USB */
--
2.1.0.27.g96db324
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
