In the programmable clock mode, the SDCLK frequency is incorrectly
assigned when the maximum clock has been assigned during probe,
this causes the SDHCI not work well.

In the programmable clock mode, when calculating the SDCLK Frequency
Select, when the maximum clock has been assigned, it is the actual
value, should not be multiplied by host->clk_mul. Otherwise, the
maximum clock is multiplied host->clk_mul by the base clock achieved
from the BASECLKF field of the Capabilities 0 Register.

Signed-off-by: Wenyou Yang <wenyou.y...@atmel.com>
---

 drivers/mmc/sdhci.c | 18 +++++++++++-------
 1 file changed, 11 insertions(+), 7 deletions(-)

diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c
index b745977b3f..161a6b1399 100644
--- a/drivers/mmc/sdhci.c
+++ b/drivers/mmc/sdhci.c
@@ -332,8 +332,7 @@ static int sdhci_set_clock(struct mmc *mmc, unsigned int 
clock)
                 */
                if (host->clk_mul) {
                        for (div = 1; div <= 1024; div++) {
-                               if ((host->max_clk * host->clk_mul / div)
-                                       <= clock)
+                               if ((host->max_clk / div) <= clock)
                                        break;
                        }
 
@@ -547,6 +546,14 @@ int sdhci_setup_cfg(struct mmc_config *cfg, struct 
sdhci_host *host,
 #ifndef CONFIG_DM_MMC_OPS
        cfg->ops = &sdhci_ops;
 #endif
+
+       /* Check whether the clock multiplier is supported or not */
+       if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300) {
+               caps_1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
+               host->clk_mul = (caps_1 & SDHCI_CLOCK_MUL_MASK) >>
+                               SDHCI_CLOCK_MUL_SHIFT;
+       }
+
        if (host->max_clk == 0) {
                if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300)
                        host->max_clk = (caps & SDHCI_CLOCK_V3_BASE_MASK) >>
@@ -555,6 +562,8 @@ int sdhci_setup_cfg(struct mmc_config *cfg, struct 
sdhci_host *host,
                        host->max_clk = (caps & SDHCI_CLOCK_BASE_MASK) >>
                                SDHCI_CLOCK_BASE_SHIFT;
                host->max_clk *= 1000000;
+               if (host->clk_mul)
+                       host->max_clk *= host->clk_mul;
        }
        if (host->max_clk == 0) {
                printf("%s: Hardware doesn't specify base clock frequency\n",
@@ -590,11 +599,6 @@ int sdhci_setup_cfg(struct mmc_config *cfg, struct 
sdhci_host *host,
        if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300) {
                if (!(caps & SDHCI_CAN_DO_8BIT))
                        cfg->host_caps &= ~MMC_MODE_8BIT;
-
-               /* Find out whether clock multiplier is supported */
-               caps_1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
-               host->clk_mul = (caps_1 & SDHCI_CLOCK_MUL_MASK) >>
-                               SDHCI_CLOCK_MUL_SHIFT;
        }
 
        if (host->host_caps)
-- 
2.11.0

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot

Reply via email to