> -----Original Message----- > From: york sun > Sent: Wednesday, March 29, 2017 10:16 PM > To: Sumit Garg <sumit.g...@nxp.com>; u-boot@lists.denx.de > Cc: Prabhakar Kushwaha <prabhakar.kushw...@nxp.com>; Ruchika Gupta > <ruchika.gu...@nxp.com>; Vini Pillai <vinitha.pil...@nxp.com> > Subject: Re: [u-boot-release] [PATCH 3/7] SECURE_BOOT: Enable chain of trust > on LS1046A platform > > On 03/23/2017 01:19 AM, Sumit Garg wrote: > > From: Vinitha Pillai-B57223 <vinitha.pil...@nxp.com> > > > > Define bootscript and its header addresses for QSPI target. Also > > define PPA header address to enable PPA validation. > > > > Signed-off-by: Vinitha Pillai <vinitha.pil...@nxp.com> > > Signed-off-by: Sumit Garg <sumit.g...@nxp.com> > > --- > > arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 1 + > > arch/arm/include/asm/arch-fsl-layerscape/config.h | 2 +- > > arch/arm/include/asm/fsl_secure_boot.h | 18 ++++++++++++++---- > > 3 files changed, 16 insertions(+), 5 deletions(-) > > > > diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig > > b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig > > index 10efb8c..fbb6642 100644 > > --- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig > > +++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig > > @@ -159,6 +159,7 @@ config SYS_LS_PPA_ESBC_ADDR > > hex "hdr address of PPA firmware loading from" > > depends on FSL_LS_PPA && CHAIN_OF_TRUST > > default 0x600c0000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1043A > > + default 0x40740000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1046A > > Why isn't the offset consistent? > > > help > > If the PPA header firmware locate at XIP flash, such as NOR or > > QSPI flash, this address is a directly memory-mapped. > > diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h > > b/arch/arm/include/asm/arch-fsl-layerscape/config.h > > index b5b08aa..1f22afd 100644 > > --- a/arch/arm/include/asm/arch-fsl-layerscape/config.h > > +++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h > > @@ -199,7 +199,7 @@ > > > > #define CONFIG_SYS_FSL_IFC_BE > > #define CONFIG_SYS_FSL_SFP_VER_3_2 > > -#define CONFIG_SYS_FSL_SNVS_LE > > +#define CONFIG_SYS_FSL_SEC_MON_BE > > #define CONFIG_SYS_FSL_SFP_BE > > #define CONFIG_SYS_FSL_SRK_LE > > #define CONFIG_KEY_REVOCATION > > diff --git a/arch/arm/include/asm/fsl_secure_boot.h > > b/arch/arm/include/asm/fsl_secure_boot.h > > index a1a3004..423c2c4 100644 > > --- a/arch/arm/include/asm/fsl_secure_boot.h > > +++ b/arch/arm/include/asm/fsl_secure_boot.h > > @@ -46,9 +46,10 @@ > > > > #endif > > > > -#if defined(CONFIG_LS1043A) || defined(CONFIG_LS2080A) > > -/* For LS1043 (ARMv8), ESBC image Address in Header is 64 bit > > - * Similiarly for LS2080 > > +#if defined(CONFIG_FSL_LAYERSCAPE) > > +/* > > + * For fsl layerscape based platforms, ESBC image Address in Header > > + * is 64 bit. > > */ > > #define CONFIG_ESBC_ADDR_64BIT > > #endif > > @@ -90,12 +91,21 @@ > > #define CONFIG_BS_ADDR_DEVICE 0x00000940 > > #define CONFIG_BS_HDR_SIZE 0x00000010 > > #define CONFIG_BS_SIZE 0x00000008 > > +#elif defined(CONFIG_QSPI_BOOT) > > +#ifdef CONFIG_ARCH_LS1046A > > +#define CONFIG_BS_HDR_ADDR_DEVICE 0x40780000 > > +#define CONFIG_BS_ADDR_DEVICE 0x40800000 > > #else > > +#error "Platform not supported" > > +#endif > > +#define CONFIG_BS_HDR_SIZE 0x00002000 > > +#define CONFIG_BS_SIZE 0x00001000 > > +#else /* Default NOR Boot */ > > #define CONFIG_BS_HDR_ADDR_DEVICE 0x600a0000 > > #define CONFIG_BS_ADDR_DEVICE 0x60060000 > > #define CONFIG_BS_HDR_SIZE 0x00002000 > > #define CONFIG_BS_SIZE 0x00001000 > > -#endif /* #ifdef CONFIG_SD_BOOT */ > > +#endif > > #define CONFIG_BS_HDR_ADDR_RAM 0x81000000 > > #define CONFIG_BS_ADDR_RAM 0x81020000 > > #endif > > > > Please consider to move these to Kconfig in the future. > > York
Sure we will move these macros to Kconfig. Sumit _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot