[U-Boot] [PATCH 2/2 V3] ppc4xx: Initialize magnetic couplers in PLU405

[Matthias Fuchs]

This patch fixes an ugly behavior of the IL712 magnetic couplers
as used on PLU405. These parts will remember their last state
over a power cycle which might cause unwanted behavior.

Signed-off-by: Matthias Fuchs <matthias.fu...@esd.eu>
---
V2:
 - use C struct to access CAN controller registes

V3:
 - move SJA1000 stuff into separate header
   (see preceding patch)
 - some renaming

 board/esd/plu405/plu405.c |   36 ++++++++++++++++++++++++++++++++++++
 include/configs/PLU405.h  |    3 ++-
 2 files changed, 38 insertions(+), 1 deletions(-)

diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c
index 1841cda..fea7b26 100644
--- a/board/esd/plu405/plu405.c
+++ b/board/esd/plu405/plu405.c
@@ -26,6 +26,7 @@
 #include <asm/io.h>
 #include <command.h>
 #include <malloc.h>
+#include <sja1000.h>
 
 #undef FPGA_DEBUG
 
@@ -45,6 +46,34 @@ const unsigned char fpgadata[] =
  */
 #include "../common/fpga.c"
 
+/*
+ * generate a short spike on the CAN tx line
+ * to bring the couplers in sync
+ */
+void init_coupler(u32 addr)
+{
+       struct sja1000_basic_s *ctrl = (struct sja1000_basic_s *)addr;
+
+       /* reset */
+       out_8(&ctrl->cr, CR_RR);
+
+       /* dominant */
+       out_8(&ctrl->btr0, 0x00); /* btr setup is required */
+       out_8(&ctrl->btr1, 0x14); /* we use 1Mbit/s */
+       out_8(&ctrl->oc, OC_TP1 | OC_TN1 | OC_POL1 |
+             OC_TP0 | OC_TN0 | OC_POL0 | OC_MODE1);
+       out_8(&ctrl->cr, 0x00);
+
+       /* delay */
+       in_8(&ctrl->cr);
+       in_8(&ctrl->cr);
+       in_8(&ctrl->cr);
+       in_8(&ctrl->cr);
+
+       /* reset */
+       out_8(&ctrl->cr, CR_RR);
+}
+
 /* Prototypes */
 int gunzip(void *, int, unsigned char *, unsigned long *);
 
@@ -198,6 +227,13 @@ int misc_init_r(void)
        out_8((void *)DUART1_BA + 1, fctr); /* write FCTR */
        out_8((void *)DUART1_BA + 3, 0);    /* write LCR */
 
+       /*
+        * Init magnetic couplers
+        */
+       if (!getenv("noinitcoupler")) {
+               init_coupler(CAN0_BA);
+               init_coupler(CAN1_BA);
+       }
        return 0;
 }
 
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 07fc715..b6740de 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -298,7 +298,8 @@
 /*
  * External Bus Controller (EBC) Setup
  */
-#define CAN_BA         0xF0000000          /* CAN Base Address         */
+#define CAN0_BA                0xF0000000          /* CAN0 Base Address        
*/
+#define CAN1_BA                0xF0000100          /* CAN1 Base Address        
*/
 #define DUART0_BA      0xF0000400          /* DUART Base Address       */
 #define DUART1_BA      0xF0000408          /* DUART Base Address       */
 #define RTC_BA         0xF0000500          /* RTC Base Address         */
-- 
1.6.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot