Dear LakeAylwyn, please make sure to post plain text only, using an internationally well accepted character set (ASCII, ISO-8859).
In message <bay113-w46cc454bc778754e4d99a4f4...@phx.gbl> you wrote: > > i use: > > make ep7312_config > make all Which tool chain are you using, and what is your setting of CROSS_COMPILE ? > then > > ÔÚº¯Êý¡®start_armboot¡¯ÖУº > /home/smile/u-boot-2009.08/lib_arm/board.c:428£º¶Ô¡®cs8900_get_enetaddr¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®ArpRequest¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:250£º¶Ô¡®eth_send¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®NetStartAgain¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:568£º¶Ô¡®eth_halt¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®NetSendPacket¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:623£º¶Ô¡®eth_send¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®NetSendUDPPacket¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:668£º¶Ô¡®eth_send¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®NetReceive¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:1263£º¶Ô¡®eth_send¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:1295£º¶Ô¡®eth_send¡¯Î´¶¨ÒåµÄÒýÓà > net/libnet.a(net.o)£ºÔÚº¯Êý¡®NetLoop¡¯ÖУº > /home/smile/u-boot-2009.08/net/net.c:342£º¶Ô¡®eth_halt¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:346£º¶Ô¡®eth_init¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:370£º¶Ô¡®eth_halt¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:481£º¶Ô¡®eth_halt¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:475£º¶Ô¡®eth_rx¡¯Î´¶¨ÒåµÄÒýÓà > /home/smile/u-boot-2009.08/net/net.c:535£º¶Ô¡®eth_halt¡¯Î´¶¨ÒåµÄÒýÓà > make: *** [u-boot] ´íÎó 1 What is this supposed to mean? I just see a lot of gibberish of unreadable characters but no error messages. Here is what I get: -> git-checkout v2009.08 Checking out files: 100% (1318/1318), done. Note: moving to 'v2009.08' which isn't a local branch If you want to create a new branch from this checkout, you may do so (now or later) by using -b with the checkout command again. Example: git checkout -b <new_branch_name> HEAD is now at 3d35d87... Prepare 2009.08 -> eldk-switch -r 4.1 arm Setup for arm-linux (using ELDK 4.1) -> echo $CROSS_COMPILE arm-linux- -> MAKEALL ep7312 Configuring for ep7312 board... eth.c:497:2: warning: #warning Ethernet driver is deprecated. Please update to use CONFIG_NET_MULTI text data bss dec hex filename 105238 3571 14936 123745 1e361 ./u-boot What exactly is your problem? Best regards, Wolfgang Denk -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de If you believe that feeling bad or worrying long enough will change a past or future event, then you are residing on another planet with a different reality system. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot