To enable DM on MPC83xx, we need pre-relocation malloc, which is
implemented in this patch.
Signed-off-by: Mario Six <mario....@gdsys.cc>
---
Changes in v2:
* Switched to r3 to hold SP modifications (as suggested by Joakim Tjernlund)
---
arch/powerpc/cpu/mpc83xx/cpu_init.c | 3 +--
arch/powerpc/cpu/mpc83xx/spl_minimal.c | 4 +---
arch/powerpc/cpu/mpc83xx/start.S | 23 +++++++++++++++++++++++
3 files changed, 25 insertions(+), 5 deletions(-)
diff --git a/arch/powerpc/cpu/mpc83xx/cpu_init.c
b/arch/powerpc/cpu/mpc83xx/cpu_init.c
index f911275b25..3a0916bdbf 100644
--- a/arch/powerpc/cpu/mpc83xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc83xx/cpu_init.c
@@ -205,8 +205,7 @@ void cpu_init_f (volatile immap_t * im)
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
- /* Clear initial global data */
- memset ((void *) gd, 0, sizeof (gd_t));
+ /* global data region was cleared in start.S */
/* system performance tweaking */
clrsetbits_be32(&im->arbiter.acr, acr_mask, acr_val);
diff --git a/arch/powerpc/cpu/mpc83xx/spl_minimal.c
b/arch/powerpc/cpu/mpc83xx/spl_minimal.c
index 845861eea7..026da12e66 100644
--- a/arch/powerpc/cpu/mpc83xx/spl_minimal.c
+++ b/arch/powerpc/cpu/mpc83xx/spl_minimal.c
@@ -23,9 +23,7 @@ void cpu_init_f (volatile immap_t * im)
/* Pointer is writable since we allocated a register for it */
gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET);
- /* Clear initial global data */
- for (i = 0; i < sizeof(gd_t); i++)
- ((char *)gd)[i] = 0;
+ /* global data region was cleared in start.S */
/* system performance tweaking */
diff --git a/arch/powerpc/cpu/mpc83xx/start.S b/arch/powerpc/cpu/mpc83xx/start.S
index c366f615e7..ff312892bc 100644
--- a/arch/powerpc/cpu/mpc83xx/start.S
+++ b/arch/powerpc/cpu/mpc83xx/start.S
@@ -263,6 +263,29 @@ in_flash:
lis r3, (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)@h
ori r3, r3, (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_GBL_DATA_OFFSET)@l
+ /* r4 = end of GD area */
+ addi r4, r3, GENERATED_GBL_DATA_SIZE
+
+ /* Zero GD area */
+ li r0, 0
+1:
+ subi r4, r4, 1
+ stb r0, 0(r4)
+ cmplw r3, r4
+ bne 1b
+
+#ifdef CONFIG_SYS_MALLOC_F_LEN
+
+#if CONFIG_SYS_MALLOC_F_LEN + GENERATED_GBL_DATA_SIZE >
CONFIG_SYS_INIT_RAM_SIZE
+#error "CONFIG_SYS_MALLOC_F_LEN too large to fit into initial RAM."
+#endif
+
+ /* r3 = new stack pointer / pre-reloc malloc area */
+ subi r3, r3, CONFIG_SYS_MALLOC_F_LEN
+
+ /* Set pointer to pre-reloc malloc area in GD */
+ stw r3, GD_MALLOC_BASE(r4)
+#endif
li r0, 0 /* Make room for stack frame header and */
stwu r0, -4(r3) /* clear final stack frame so that */
stwu r0, -4(r3) /* stack backtraces terminate cleanly */
--
2.11.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
