Hi Folks, While attempting to address the warning for SDP3430 as pointed out by dirk in [1], I did a patch corresponding to what was done for EVM(353x) as in [2]. unfortunately, this wont work for me, I get: U-Boot 2009.08-00515-gfea6a55-dirty (Oct 12 2009 - 14:03:23)
OMAP3530-GP ES3.0, CPU-OPP2 L3-165MHz OMAP3 SDP3430 board + LPDDR/NOR I2C: ready DRAM: 128 MB Flash: 128 MB In: serial Out: serial Err: serial smc911x: Invalid chip endian 0xdee0013d Net: No ethernet found. OMAP34XX SDP # and no network, using LEGACY driver seems to be working just great for me. Note: in my patch [2], I did try both CONFIG_SMC911X_32_BIT and CONFIG_SMC911X_16_BIT with no luck either way. I even tried to hack the driver by skipping the supported chip detection code, but the driver still did not work for me. scanning a little more in the git repo, I see all the ancient boards of OMAP family - 5912,2420 etc.. still have LEGACY driver being used.. I am pretty sure I must be missing something here and appreciate any guidance folks can give me on this.. -- Regards, Nishanth Menon Ref: [1] http://www.nabble.com/forum/Permalink.jtp?root=25837696&post=25841367&page=y [2] From fea6a55cb67b3fda1d93da74b2fe68fb25376e7e Mon Sep 17 00:00:00 2001 From: Nishanth Menon <n...@ti.com> Date: Mon, 12 Oct 2009 13:54:17 -0500 Subject: [BAD][PATCH] TI OMAP3: SDP3430: dont use legacy ethernet driver Stop using the LEGACY driver and use NET_MULTI this also removes the build warning for SDP3430 --- board/ti/sdp3430/sdp.c | 8 +++++--- include/configs/omap3_sdp3430.h | 7 ++++--- 2 files changed, 9 insertions(+), 6 deletions(-) diff --git a/board/ti/sdp3430/sdp.c b/board/ti/sdp3430/sdp.c index 40cf26f..85181c8 100644 --- a/board/ti/sdp3430/sdp.c +++ b/board/ti/sdp3430/sdp.c @@ -22,6 +22,7 @@ * MA 02111-1307 USA */ #include <common.h> +#include <netdev.h> #include <twl4030.h> #include <asm/io.h> #include <asm/arch/mux.h> @@ -121,8 +122,8 @@ int board_init(void) return 0; } -#define LAN_RESET_REGISTER (CONFIG_LAN91C96_BASE + 0x01c) -#define ETH_CONTROL_REG (CONFIG_LAN91C96_BASE + 0x30b) +#define LAN_RESET_REGISTER (CONFIG_SMC911X_BASE + 0x01c) +#define ETH_CONTROL_REG (CONFIG_SMC911X_BASE + 0x30b) /** * @brief ether_init Take the Ethernet controller out of reset and wait @@ -130,7 +131,7 @@ int board_init(void) */ static void ether_init(void) { -#ifdef CONFIG_DRIVER_LAN91C96 +#ifdef CONFIG_SMC911X int cnt = 20; writew(0x0, LAN_RESET_REGISTER); @@ -155,6 +156,7 @@ static void ether_init(void) writeb(readb(ETH_CONTROL_REG) & ~0x1, ETH_CONTROL_REG); udelay(1000); + smc911x_initialize(0, CONFIG_SMC911X_BASE); reset_err_out: return; diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h index 229dc5e..7b0a248 100644 --- a/include/configs/omap3_sdp3430.h +++ b/include/configs/omap3_sdp3430.h @@ -200,9 +200,10 @@ */ #if defined(CONFIG_CMD_NET) -#define CONFIG_DRIVER_LAN91C96 -#define CONFIG_LAN91C96_BASE DEBUG_BASE -#define CONFIG_LAN91C96_EXT_PHY +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE DEBUG_BASE #define CONFIG_BOOTP_SEND_HOSTNAME /* -- 1.6.3.3 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
