On 24/10/2016 09:53, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sba...@denx.de> wrote:
>> Hi Jagan,
>>
>> On 17/10/2016 05:40, Jagan Teki wrote:
>>> Hi Stefano,
>>>
>>> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jt...@openedev.com> wrote:
>>>> Hi Stefano,
>>>>
>>>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.t...@gmail.com>
>>>> wrote:
>>>>> Hi Stefano,
>>>>>
>>>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jt...@openedev.com> wrote:
>>>>>> From: Jagan Teki <ja...@amarulasolutions.com>
>>>>>>
>>>>>> This series supports Engicam i.CoreM6 QDL modules on top of
>>>>>> u-boot-imx/master
>>>>>> and test on the respective starter kits as well.
>>>>>>
>>>>>> Tested both MMC and NAND boot.
>>>>>>
>>>>>> Changes for v7:
>>>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>> - Rebase on u-boot-imx/master
>>>>>>
>>>>>> Changes for v6:
>>>>>> - Rebase to u-boot-imx/master
>>>>>> - Move few SPL configs to defconfigs
>>>>>>
>>>>>> Changes for v5:
>>>>>> - Add NAND support
>>>>>>
>>>>>> Changes for v4:
>>>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch
>>>>>> - Updated ENV configs along with comments
>>>>>> - Restructured configs for more readability
>>>>>> - Add CONFIG_ENV_OVERWRITE
>>>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>>>>>>
>>>>>> Changes for v3:
>>>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs
>>>>>> base" patch
>>>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
>>>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL
>>>>>> - Add is_mx6dl()
>>>>>> - Add is_mx6solo()
>>>>>> - Use is_mx6dq()
>>>>>> - Add last commit sha1 and header in pull devicetree files from
>>>>>> Linux
>>>>>>
>>>>>> Changes for v2:
>>>>>> - Make static to local iomux structure in board file
>>>>>> - Corrected rowaddr in mx6_ddr3_cfg
>>>>>> - Used imx_ddr_size
>>>>>> - Add FEC support and tested the same
>>>>>> - Add DM_GPIO, DM_MMC support
>>>>>> - Add pinctrl support
>>>>>> - Add devicetree support
>>>>>>
>>>>>> Jagan Teki (21):
>>>>>> serial: Kconfig: Add MXC_UART entry
>>>>>> thermal: Kconfig: Add IMX_THERMAL entry
>>>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
>>>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
>>>>>> net: Kconfig: Add FEC_MXC entry
>>>>>> imx6: icorem6: Add ENET support
>>>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g
>>>>>> arm: dts: Add devicetree for i.MX6DL
>>>>>> arm: dts: Add devicetree for i.MX6DQL
>>>>>> arm: dts: imx6dl: Add pinctrl defines
>>>>>> dt-bindings: clock: imx6qdl: Add clock defines
>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
>>>>>> imx6q: icorem6: Enable pinctrl driver
>>>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support
>>>>>> arm: dts: Add devicetree for i.MX6Q
>>>>>> arm: dts: imx6q: Add pinctrl defines
>>>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
>>>>>> mtd: nand: Kconfig: Add NAND_MXS entry
>>>>>> imx6: icorem6: Add NAND support
>>>>>> imx6: icorem6: Enable MTD device support
>>>>>> imx6: icorem6: Add default mtd nand partition table
>>>>>
>>>>> All set now, please do apply.
>>>>
>>>> Let me know if you still find any issues, otherwise apply this.
>>>>
>>>
>>> Any help?
>>
>> Sorry, I was last week at ELCE - I will go on with your patches (and the
>> other ones left pending) this week.
>
> Please apply this, I need to rebase on top of tom/master and send few
> more series.
>
Tried again, it does not compile clean.
drivers/mmc/fsl_esdhc.c:715:21: error: variable 'esdhc_ops' has
initializer but incomplete type
static const struct mmc_ops esdhc_ops = {
^
drivers/mmc/fsl_esdhc.c:716:2: error: unknown field 'send_cmd' specified
in initializer
.send_cmd = esdhc_send_cmd,
^
drivers/mmc/fsl_esdhc.c:716:14: warning: excess elements in struct
initializer
.send_cmd = esdhc_send_cmd,
^
drivers/mmc/fsl_esdhc.c:716:14: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:717:2: error: unknown field 'set_ios' specified
in initializer
.set_ios = esdhc_set_ios,
^
drivers/mmc/fsl_esdhc.c:717:13: warning: excess elements in struct
initializer
.set_ios = esdhc_set_ios,
^
drivers/mmc/fsl_esdhc.c:717:13: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:718:2: error: unknown field 'init' specified in
initializer
.init = esdhc_init,
^
drivers/mmc/fsl_esdhc.c:718:11: warning: excess elements in struct
initializer
.init = esdhc_init,
^
drivers/mmc/fsl_esdhc.c:718:11: note: (near initialization for 'esdhc_ops')
drivers/mmc/fsl_esdhc.c:719:2: error: unknown field 'getcd' specified in
initializer
.getcd = esdhc_getcd,
^
drivers/mmc/fsl_esdhc.c:719:12: warning: excess elements in struct
initializer
.getcd = esdhc_getcd,
^
drivers/mmc/fsl_esdhc.c:719:12: note: (near initialization for 'esdhc_ops')
Can you check it ?
Regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
