On 10/12/2016 10:11 PM, Alexandr Bochkarev wrote: > Now i boot marsboard from sd card with new config
Good. > > => mmc list > SUNXI SD/MMC: 0 (SD) > SUNXI SD/MMC: 1 > > => mmc info > Device: SUNXI SD/MMC > Manufacturer ID: 2 > OEM: 544d > Name: SA04G > Tran Speed: 50000000 > Rd Block Len: 512 > SD version 3.0 > High Capacity: Yes > Capacity: 3.6 GiB > Bus Width: 4-bit > Erase Group Size: 512 Bytes > > => mmc part > > Partition Map for MMC device 0 -- Partition Type: DOS > > Part.Start Sector.Num Sectors.UUID..Type > 1.2048 .12288 .da1dcf13-01.83 > 2.14336 .204800 .da1dcf13-02.83 > 3.219136 .204800 .da1dcf13-03.83 > 4.423936 .409600 .da1dcf13-04.05 Extd > 5.425984 .204800 .da1dcf13-05.83 > 6.632832 .200704 .da1dcf13-06.83 > > => mmc dev 1 > CMD_SEND:0 > ..ARG... 0x00000000 > ..MMC_RSP_NONE > CMD_SEND:8 > ..ARG... 0x000001AA > ..RET... -110 > CMD_SEND:55 > ..ARG... 0x00000000 > ..RET... -110 > CMD_SEND:0 > ..ARG... 0x00000000 > ..MMC_RSP_NONE > CMD_SEND:1 > ..ARG... 0x00000000 > ..MMC_RSP_R3,4.. 0x00FF8080 > CMD_SEND:1 > ..ARG... 0x40300000 > ..MMC_RSP_R3,4.. 0x00FF8080 > CMD_SEND:0 > ..ARG... 0x00000000 > ..MMC_RSP_NONE > CMD_SEND:1 > ..ARG... 0x40300000 > ..MMC_RSP_R3,4.. 0x00FF8080 > CMD_SEND:1 > ..ARG... 0x40300000 > ..MMC_RSP_R3,4.. 0xC0FF8080 > CMD_SEND:2 > ..ARG... 0x00000000 > ..MMC_RSP_R2.. 0x1501004D > .. .. 0x34473146 > .. .. 0x42030B01 > .. .. 0x7585C009 > > .....DUMPING DATA > .....000 - 15 01 00 4D > .....004 - 34 47 31 46 > .....008 - 42 03 0B 01 > .....012 - 75 85 C0 09 > CMD_SEND:3 > ..ARG... 0x00010000 > ..MMC_RSP_R1,5,6,7 . 0x00000500 > CMD_SEND:9 > ..ARG... 0x00010000 > ..MMC_RSP_R2.. 0xD0270132 > .. .. 0x0F5903FF > .. .. 0xF6DBFFE7 > .. .. 0x8A404057 > > .....DUMPING DATA > .....000 - D0 27 01 32 > .....004 - 0F 59 03 FF > .....008 - F6 DB FF E7 > .....012 - 8A 40 40 57 > CMD_SEND:13 > ..ARG... 0x00010000 > ..MMC_RSP_R1,5,6,7 . 0x00000700 > CURR STATE:3 > CMD_SEND:7 > ..ARG... 0x00010000 > ..MMC_RSP_R1,5,6,7 . 0x00000700 > CMD_SEND:8 > ..ARG... 0x00000000 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:8 > ..ARG... 0x00000000 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:6 > ..ARG... 0x03B90100 > ..MMC_RSP_R1b.. 0x00000900 > CMD_SEND:13 > ..ARG... 0x00010000 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CURR STATE:4 > CMD_SEND:8 > ..ARG... 0x00000000 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:6 > ..ARG... 0x03B70100 > ..RET... -110 Maybe at here..switch to buswidth..but failed. define debug() in your mmc driver..or enable CONFIG_DEBUG..then you can see all debug message. > CMD_SEND:16 > ..ARG... 0x00000200 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:17 > ..ARG... 0x00000000 > ..RET... -110 > mmc_bread: Failed to read blocks > CMD_SEND:16 > ..ARG... 0x00000200 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:17 > ..ARG... 0x00000000 > ..RET... -110 > mmc_bread: Failed to read blocks > CMD_SEND:16 > ..ARG... 0x00000200 > ..MMC_RSP_R1,5,6,7 . 0x00000900 > CMD_SEND:18 > ..ARG... 0x00000040 > ..RET... -110 > mmc_bread: Failed to read blocks > switch to partitions #0, OK > mmc1(part 0) is current device > > > => mmc info > Device: SUNXI SD/MMC > Manufacturer ID: 15 > OEM: 100 > Name: M4G1F > Tran Speed: 52000000 > Rd Block Len: 512 > MMC version 4.4.1 > High Capacity: Yes > Capacity: 3.6 GiB > Bus Width: 1-bit > Erase Group Size: 512 KiB > HC WP Group Size: 4 MiB > User Capacity: 3.6 GiB WRREL > Boot Capacity: 1 MiB ENH > RPMB Capacity: 128 KiB ENH > > => mmc part > ## Unknown partition table type 0 > > > > > eMMC burned same image as SD. And seems like it doesnt switched to 4-bit bus > width If you're setting MMC_MODE_8BIT..try to remove it.. > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
