Hi Stefano, Le Thu, 6 Oct 2016 09:21:13 +0200, Stefano Babic <sba...@denx.de> a écrit :
> Hi Albert, > > On 26/09/2016 09:08, Albert ARIBAUD (3ADEV) wrote: > > BK4R1 is basically PCM052 with the following differences > > or quirks: > > > > 1) it has 512MB of DDR using MT41K256M16HA_125IT, > > while the PCM052 has 256MB using MT41J128M16HA_15EIT; > > > > 2) it has 1GB of NAND. The size increase is supported > > by the env directly; > > > > 3) its Ethernet ports are physicaly tied together until > > GPIO 122 is raised. As this is a safety feature U-Boot > > does not untie the ports except if it needs networking, > > for instance when doing NAND updates via TFTP; > > > > 4) it has a USB hub which may remain in reset if GPIO 130 > > is not raised. This is done unconditionally at boot; > > > > 5) It has two NOR SPI flash chips on QSPI. > > > > This series has been run through checkpatch and has no errors > > or warning except the following one: > > > > warning: arch/arm/Kconfig,681: please write a > > paragraph that describes the config symbol fully > > > > Which I believe does not apply, as target configs in this file > > never have descriptions. > > > > > > Albert ARIBAUD (3ADEV) (6): > > pcm052: fix MTD partitioning > > pcm052: remove target-specific dtb name from env > > pcm052: add 'm4go' command > > tools: mkimage: add support for Vybrid image format > > pcm052: allow specifying onboard DDR size in configs > > pcm052: add new BK4r1 target based on PCM052 SoM > > > > Makefile | 6 ++ > > arch/arm/Kconfig | 4 + > > arch/arm/config.mk | 3 + > > arch/arm/cpu/armv7/vf610/Makefile | 5 + > > arch/arm/dts/Makefile | 3 +- > > arch/arm/dts/bk4r1.dts | 48 +++++++++ > > arch/arm/dts/vf.dtsi | 4 +- > > board/phytec/pcm052/Kconfig | 24 +++++ > > board/phytec/pcm052/pcm052.c | 206 > > ++++++++++++++++++++++++++++---------- > > common/image.c | 1 + > > configs/bk4r1_defconfig | 32 ++++++ > > include/configs/bk4r1.h | 33 ++++++ > > include/configs/pcm052.h | 78 ++++++++++----- > > include/image.h | 1 + > > tools/Makefile | 1 + > > tools/vybridimage.c | 164 ++++++++++++++++++++++++++++++ > > 16 files changed, 535 insertions(+), 78 deletions(-) > > create mode 100644 arch/arm/dts/bk4r1.dts > > create mode 100644 configs/bk4r1_defconfig > > create mode 100644 include/configs/bk4r1.h > > create mode 100644 tools/vybridimage.c > > > > It looks like that CONFIG_CMD_UBI for bk4r1 is not set and I get build > errors. Hmm... What U-Boot commit do you apply above? > Is it ok for you if I add directly this by applying ? I'll check this and let you know later today. > diff --git a/configs/bk4r1_defconfig b/configs/bk4r1_defconfig > index 3994459..26d9e81 100644 > --- a/configs/bk4r1_defconfig > +++ b/configs/bk4r1_defconfig > @@ -30,3 +30,4 @@ CONFIG_SPI_FLASH=y > CONFIG_SPI_FLASH_STMICRO=y > CONFIG_SPI_FLASH_MTD=y > CONFIG_CMD_DM=y > +CONFIG_CMD_UBI=y > > Regards, > Stefano > Cordialement, Albert ARIBAUD 3ADEV _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
