Hi,
On 9 August 2016 at 12:14, Sanchayan Maity <maitysancha...@gmail.com> wrote:
>
> Add driver model support for Vybrid USB driver.
>
> Signed-off-by: Sanchayan Maity <maitysancha...@gmail.com>
> ---
> drivers/usb/host/ehci-vf.c | 208
> +++++++++++++++++++++++++++++++++++++++++++--
> 1 file changed, 201 insertions(+), 7 deletions(-)
Reviewed-by:: Simon Glass <s...@chromium.org>
>
> diff --git a/drivers/usb/host/ehci-vf.c b/drivers/usb/host/ehci-vf.c
> index 61789dd..f6f9efb 100644
> --- a/drivers/usb/host/ehci-vf.c
> +++ b/drivers/usb/host/ehci-vf.c
> @@ -8,16 +8,20 @@
> */
>
> #include <common.h>
> +#include <dm.h>
> #include <usb.h>
> #include <errno.h>
> #include <linux/compiler.h>
> #include <asm/io.h>
> +#include <asm-generic/gpio.h>
> #include <asm/arch/clock.h>
> #include <asm/arch/imx-regs.h>
> #include <asm/arch/crm_regs.h>
> #include <asm/imx-common/iomux-v3.h>
> #include <asm/imx-common/regs-usbphy.h>
> #include <usb/ehci-ci.h>
> +#include <libfdt.h>
> +#include <fdtdec.h>
>
> #include "ehci.h"
>
> @@ -32,6 +36,8 @@
> #define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
> #define UCMD_RESET (1 << 1) /* controller reset */
>
> +DECLARE_GLOBAL_DATA_PTR;
> +
> static const unsigned phy_bases[] = {
> USB_PHY0_BASE_ADDR,
> USB_PHY1_BASE_ADDR,
This should be converted to DT, perhaps in a follow-up patch.
> @@ -131,24 +137,39 @@ int __weak board_ehci_hcd_init(int port)
> return 0;
> }
>
> +int ehci_vf_common_init(struct usb_ehci *ehci, int index)
> +{
> + int ret;
> +
> + /* Do board specific initialisation */
nit: board-specific
> + ret = board_ehci_hcd_init(index);
> + if (ret)
> + return ret;
> +
> + usb_power_config(index);
> + usb_oc_config(index);
> + usb_internal_phy_clock_gate(index);
> + usb_phy_enable(index, ehci);
> +
> + return 0;
> +}
> +
> +#ifndef CONFIG_DM_USB
> int ehci_hcd_init(int index, enum usb_init_type init,
> struct ehci_hccr **hccr, struct ehci_hcor **hcor)
> {
> struct usb_ehci *ehci;
> enum usb_init_type type;
> + int ret;
>
> if (index >= ARRAY_SIZE(nc_reg_bases))
> return -EINVAL;
>
> ehci = (struct usb_ehci *)nc_reg_bases[index];
>
> - /* Do board specific initialisation */
> - board_ehci_hcd_init(index);
> -
> - usb_power_config(index);
> - usb_oc_config(index);
> - usb_internal_phy_clock_gate(index);
> - usb_phy_enable(index, ehci);
> + ret = ehci_vf_common_init(index);
> + if (ret)
> + return ret;
>
> *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
> *hcor = (struct ehci_hcor *)((uint32_t)*hccr +
> @@ -175,3 +196,176 @@ int ehci_hcd_stop(int index)
> {
> return 0;
> }
> +#else
> +/* Possible port types (dual role mode) */
> +enum dr_mode {
> + DR_MODE_NONE = 0,
> + DR_MODE_HOST, /* supports host operation */
> + DR_MODE_DEVICE, /* supports device operation */
> + DR_MODE_OTG, /* supports both */
> +};
> +
> +struct ehci_vf_priv_data {
> + struct ehci_ctrl ctrl;
> + struct usb_ehci *ehci;
> + struct gpio_desc cdet_gpio;
> + enum usb_init_type init_type;
> + enum dr_mode dr_mode;
> + u32 portnr;
> +};
> +
> +static int vf_usb_ofdata_to_platdata(struct udevice *dev)
> +{
> + struct ehci_vf_priv_data *priv = dev_get_priv(dev);
> + const void *dt_blob = gd->fdt_blob;
> + int node = dev->of_offset;
> + const char *mode;
> +
> + priv->portnr = dev->seq;
> +
> + priv->ehci = (struct usb_ehci *)dev_get_addr(dev);
> + mode = fdt_getprop(dt_blob, node, "dr_mode", NULL);
> + if (mode) {
> + if (0 == strcmp(mode, "host")) {
You can say
if (!strcmp...
if you like. Up to you.
> + priv->dr_mode = DR_MODE_HOST;
> + priv->init_type = USB_INIT_HOST;
> + } else if (0 == strcmp(mode, "peripheral")) {
> + priv->dr_mode = DR_MODE_DEVICE;
> + priv->init_type = USB_INIT_DEVICE;
> + } else if (0 == strcmp(mode, "otg")) {
> + priv->dr_mode = DR_MODE_OTG;
> + /*
> + * We set init_type to device by default when OTG
> + * mode is requested. If a valid gpio is provided
> + * we will switch the init_type based on the state
> + * of the gpio pin.
> + */
> + priv->init_type = USB_INIT_DEVICE;
> + } else {
> + debug("%s: Cannot decode dr_mode '%s'\n",
> + __func__, mode);
> + return -EINVAL;
> + }
> + } else {
> + priv->dr_mode = DR_MODE_HOST;
> + priv->init_type = USB_INIT_HOST;
> + }
> +
> + if (priv->dr_mode == DR_MODE_OTG) {
> + gpio_request_by_name_nodev(dt_blob, node, "fsl,cdet-gpio", 0,
> + &priv->cdet_gpio, GPIOD_IS_IN);
> + if (dm_gpio_is_valid(&priv->cdet_gpio)) {
> + if (dm_gpio_get_value(&priv->cdet_gpio))
> + priv->init_type = USB_INIT_DEVICE;
> + else
> + priv->init_type = USB_INIT_HOST;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int vf_init_after_reset(struct ehci_ctrl *dev)
> +{
> + struct ehci_vf_priv_data *priv = dev->priv;
> + enum usb_init_type type = priv->init_type;
> + struct usb_ehci *ehci = priv->ehci;
> + int ret;
> +
> + ret = ehci_vf_common_init(priv->ehci, priv->portnr);
> + if (ret)
> + return ret;
> +
> + if (type == USB_INIT_DEVICE)
> + return 0;
> +
> + setbits_le32(&ehci->usbmode, CM_HOST);
> + writel((PORT_PTS_UTMI | PORT_PTS_PTW), &ehci->portsc);
> + setbits_le32(&ehci->portsc, USB_EN);
> +
> + mdelay(10);
> +
> + return 0;
> +}
> +
> +static const struct ehci_ops vf_ehci_ops = {
> + .init_after_reset = vf_init_after_reset
> +};
> +
> +static int vf_usb_bind(struct udevice *dev)
> +{
> + static int num_controllers;
> +
> + /*
> + * Without this hack, if we return ENODEV for USB Controller 0, on
> + * probe for the next controller, USB Controller 1 will be given a
> + * sequence number of 0. This conflicts with our requirement of
> + * sequence numbers while initialising the peripherals.
> + */
> + dev->req_seq = num_controllers;
> + num_controllers++;
Yes, but if you use DT you can define the number using an alias.
> +
> + return 0;
> +}
> +
> +static int ehci_usb_probe(struct udevice *dev)
> +{
> + struct usb_platdata *plat = dev_get_platdata(dev);
> + struct ehci_vf_priv_data *priv = dev_get_priv(dev);
> + struct usb_ehci *ehci = priv->ehci;
> + struct ehci_hccr *hccr;
> + struct ehci_hcor *hcor;
> + int ret;
> +
> + ret = ehci_vf_common_init(ehci, priv->portnr);
> + if (ret)
> + return ret;
> +
> + if (priv->init_type != plat->init_type)
> + return -ENODEV;
-ENODEV means that there is no device. I think -EINVAL or -EPERM or
something else would be better.
> +
> + if (priv->init_type == USB_INIT_HOST) {
> + setbits_le32(&ehci->usbmode, CM_HOST);
> + writel((PORT_PTS_UTMI | PORT_PTS_PTW), &ehci->portsc);
> + setbits_le32(&ehci->portsc, USB_EN);
> + }
> +
> + mdelay(10);
Why? Please add a comment. That's a really long time.
> +
> + hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
> + hcor = (struct ehci_hcor *)((uint32_t)hccr +
> + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
> +
> + return ehci_register(dev, hccr, hcor, &vf_ehci_ops, 0,
> priv->init_type);
> +}
> +
> +static int ehci_usb_remove(struct udevice *dev)
> +{
> + int ret;
> +
> + ret = ehci_deregister(dev);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static const struct udevice_id vf_usb_ids[] = {
> + { .compatible = "fsl,vf610-usb" },
> + { }
> +};
> +
> +U_BOOT_DRIVER(usb_ehci) = {
> + .name = "ehci_vf",
> + .id = UCLASS_USB,
> + .of_match = vf_usb_ids,
> + .bind = vf_usb_bind,
> + .probe = ehci_usb_probe,
> + .remove = ehci_usb_remove,
> + .ops = &ehci_usb_ops,
> + .ofdata_to_platdata = vf_usb_ofdata_to_platdata,
> + .platdata_auto_alloc_size = sizeof(struct usb_platdata),
> + .priv_auto_alloc_size = sizeof(struct ehci_vf_priv_data),
> + .flags = DM_FLAG_ALLOC_PRIV_DMA,
> +};
> +#endif
> --
> 2.9.2
Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
