On 06/08/2016 12:35 AM, Steve Rae wrote: > Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the > physical interface to be 8-bit (rather than 16-bit). > > Signed-off-by: Steve Rae <s...@broadcom.com>
Applied both, thanks. > --- > from [1] (line ~124) > > /* The Kona PHY supports an 8-bit wide UTMI interface */ > [...snip...] > > module_platform_driver(bcm_kona_usb2_driver); > > MODULE_ALIAS("platform:bcm-kona-usb2"); > MODULE_AUTHOR("Matt Porter <mpor...@linaro.org>"); > MODULE_DESCRIPTION("BCM Kona USB 2.0 PHY driver"); > MODULE_LICENSE("GPL v2"); > > [1] > https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/drivers/phy/phy-bcm-kona-usb2.c > > Changes in v5: None > Changes in v4: > - split defconfig's into separate patch (per Marek) > > Changes in v3: > - implement Marek's suggestion > > Changes in v2: > - implement as Kconfig > > drivers/usb/gadget/Kconfig | 10 ++++++++++ > drivers/usb/gadget/dwc2_udc_otg.c | 4 ++++ > 2 files changed, 14 insertions(+) > > diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig > index a35a1c7..ae62476 100644 > --- a/drivers/usb/gadget/Kconfig > +++ b/drivers/usb/gadget/Kconfig > @@ -52,6 +52,16 @@ config USB_GADGET_DWC2_OTG > driver to operate in Peripheral mode. This option requires > USB_GADGET to be enabled. > > +if USB_GADGET_DWC2_OTG > + > +config USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 > + bool "DesignWare USB2.0 HS OTG controller 8-bit PHY bus width" > + help > + Set the Designware USB2.0 high-speed OTG controller > + PHY interface width to 8 bits, rather than the default (16 bits). > + > +endif # USB_GADGET_DWC2_OTG > + > config CI_UDC > bool "ChipIdea device controller" > select USB_GADGET_DUALSPEED > diff --git a/drivers/usb/gadget/dwc2_udc_otg.c > b/drivers/usb/gadget/dwc2_udc_otg.c > index cb20b00..a23278d 100644 > --- a/drivers/usb/gadget/dwc2_udc_otg.c > +++ b/drivers/usb/gadget/dwc2_udc_otg.c > @@ -415,7 +415,11 @@ static void reconfig_usbd(struct dwc2_udc *dev) > |0<<7 /* Ulpi DDR sel*/ > |0<<6 /* 0: high speed utmi+, 1: full speed serial*/ > |0<<4 /* 0: utmi+, 1:ulpi*/ > +#ifdef CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 > + |0<<3 /* phy i/f 0:8bit, 1:16bit*/ > +#else > |1<<3 /* phy i/f 0:8bit, 1:16bit*/ > +#endif > |0x7<<0; /* HS/FS Timeout**/ > > if (dev->pdata->usb_gusbcfg) > -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot