[U-Boot] [PATCH 09/18] imx: ventana: gsc: add gsc sleep command

[Tim Harvey]

The Gateworks System Controller on Ventana boards has the ability to
disable the board's primary power supply until the RTC hits a specific
time. When sleeping a button-down event on the GSC user pushbutton will
wake the board before it's wake time has been reached. This feature is
referred to as GSC sleep.

Add a command to invoke sleep mode for a specified number of seconds.

Signed-off-by: Tim Harvey <thar...@gateworks.com>
---
 board/gateworks/gw_ventana/gsc.c | 46 +++++++++++++++++++++++++++++++++++++++-
 1 file changed, 45 insertions(+), 1 deletion(-)

diff --git a/board/gateworks/gw_ventana/gsc.c b/board/gateworks/gw_ventana/gsc.c
index 4f26bfd..2555824 100644
--- a/board/gateworks/gw_ventana/gsc.c
+++ b/board/gateworks/gw_ventana/gsc.c
@@ -160,6 +160,48 @@ int gsc_boot_wd_disable(void)
 }
 
 #ifdef CONFIG_CMD_GSC
+static int do_gsc_sleep(cmd_tbl_t *cmdtp, int flag, int argc,
+                       char * const argv[])
+{
+       unsigned char reg;
+       unsigned long secs = 0;
+
+       if (argc < 2)
+               return CMD_RET_USAGE;
+
+       secs = simple_strtoul(argv[1], NULL, 10);
+       printf("GSC Sleeping for %ld seconds\n", secs);
+
+       i2c_set_bus_num(0);
+       reg = (secs >> 24) & 0xff;
+       if (gsc_i2c_write(GSC_SC_ADDR, 9, 1, &reg, 1))
+               goto error;
+       reg = (secs >> 16) & 0xff;
+       if (gsc_i2c_write(GSC_SC_ADDR, 8, 1, &reg, 1))
+               goto error;
+       reg = (secs >> 8) & 0xff;
+       if (gsc_i2c_write(GSC_SC_ADDR, 7, 1, &reg, 1))
+               goto error;
+       reg = secs & 0xff;
+       if (gsc_i2c_write(GSC_SC_ADDR, 6, 1, &reg, 1))
+               goto error;
+       if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1))
+               goto error;
+       reg |= (1 << 2);
+       if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1))
+               goto error;
+       reg &= ~(1 << 2);
+       reg |= 0x3;
+       if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, &reg, 1))
+               goto error;
+
+       return CMD_RET_SUCCESS;
+
+error:
+       printf("i2c error\n");
+       return CMD_RET_FAILURE;
+}
+
 static int do_gsc_wd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
        unsigned char reg;
@@ -206,13 +248,15 @@ static int do_gsc(cmd_tbl_t *cmdtp, int flag, int argc, 
char * const argv[])
 
        if (strcasecmp(argv[1], "wd") == 0)
                return do_gsc_wd(cmdtp, flag, --argc, ++argv);
+       else if (strcasecmp(argv[1], "sleep") == 0)
+               return do_gsc_sleep(cmdtp, flag, --argc, ++argv);
 
        return CMD_RET_USAGE;
 }
 
 U_BOOT_CMD(
        gsc, 4, 1, do_gsc, "GSC configuration",
-       "[wd enable [30|60]]|[wd disable]\n"
+       "[wd enable [30|60]]|[wd disable]|[sleep <secs>]\n"
        );
 
 #endif /* CONFIG_CMD_GSC */
-- 
1.9.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot